ENGLISH

Setting items

Setting contents

Front Height

 

ON : Use the front height channel.

 

Set whether or not to use

OFF : Do not use the front height channel.

the front height channel.

This can also be set by pressing

.

 

 

 

Subwoofer ATT

 

ON : The input from the subwoofer channel is attenuated.

Attenuate

subwoofer level

OFF : The input from the subwoofer channel is not attenuated. Usually use

when using EXT. IN mode.

in this mode.

 

 

 

 

Set this to “ON” if the subwoofer channel level seems too high when

 

 

 

playing audio signal.

 

Subwoofer

 

ON : The subwoofer is used.

 

Turn subwoofer output on

OFF : The subwoofer is not used.

 

and off.

 

 

 

 

Default

 

 

Yes : Reset to the defaults.

 

Restores

all the

surround

No : Do not reset to the defaults.

 

parameter

settings

to their

 

 

defaults.

 

 

 

 

Adjusting the Tone (Tone Control)

 

Default settings are underlined.

 

 

 

 

Setting items

Setting contents

 

 

Tone Control

ON : Allow tone adjustment (treble, bass).

Sets the tone control function OFF : Playback without tone adjustment.

ON and OFF.

The tone cannot be adjusted when in the DIRECT mode.

 

This can be set when “Dynamic EQ” (vpage 49) is set to “OFF”.

Bass–6dB ~ +6dB (0dB)

Adjusts the low frequencies.

 

This can be set when “Tone Control” is set to “ON”.

Treble

 

–6dB ~ +6dB (0dB)

Adjusts

the

high

frequencies.

 

 

This can be set when “Tone Control” is set to “ON”.

Adjusting the Sound and Picture Quality (Audio/Video Adjust)

Adjusting MultEQ®, Dynamic EQ™, Dynamic Volume™ Settings (Audyssey Settings)

Default settings are underlined.

•When “Audyssey™ Auto Setup” (vpage 22) procedure is performed, “MultEQ”, “Dynamic EQ” and “Dynamic Volume” functions are enabled.

•Operating conditions for each function

•

Dynamic EQ :MultEQ

 

When “MultEQ” is set to “ON”

Dynamic EQ

•

Dynamic Volume :

 

When “Dynamic EQ” is set to “ON”

Dynamic Volume

•

Setting :

Setting

 

When “Dynamic Volume” is set to “ON”

 

 

NOTE

If the speaker settings are changed after “Audyssey Auto Setup” is performed, “MultEQ”, “Dynamic EQ” and “Dynamic Volume” functions cannot be selected and “Run Audyssey” is displayed.

If this happens, either perform “Audyssey Auto Setup” again, or perform the “Restore” operation (vpage 26) to restore the settings to as they were after “Audyssey Auto Setup”was performed.

Setting items

 

Setting contents

 

 

 

 

 

MultEQ

 

 

 

Audyssey : Optimize frequency response of all speakers.

Corrects

the

frequency

Audyssey Byp.L/R : Optimize frequency response of speakers except

response

of

the

different

front L and R speakers.

 

speakers.

 

 

 

Audyssey Flat : Optimize frequency response of all speakers to flat

NOTE

 

 

 

response.

 

 

 

 

Manual : Apply frequency response set with “Manual EQ” (vpage 50).

• “MultEQ”

and

“Manual

OFF : “MultEQ” equalization cannot be used.

EQ”

settings for which

• When “Audyssey”, “Audyssey Byp. L/R” or “Audyssey Flat” is

“Not Used” has been set at

“EQ Customize” (vpage

selected, “

” lights.

31) cannot be selected.

• After running Audyssey Auto Setup, if the Speaker Configuration,

• When

using headphones,

Distance, Channel Level, and Crossover Frequency have changed

“MultEQ” is set to “OFF”.

without increasing the number of speakers measured, only

“ ” lights.

•This can also be set by pressing .

See overleaf

Specifications Troubleshooting Information Control Remote Zone-Multi Playback Settings Connections Started Getting

Remote control

 

 

 

 

 

 

 

 

:

Displaying the menu

: Moves the cursor (Up/Down/Left/Right)

: Decision the setting

: Return to previous menu

48

operation buttons

 

 

Cancel the menu