ENGLISH

Getting

 

 

 

Installing/Setting the Speakers

 

 

 

 

 

 

 

 

sSet the “Amp Assign” Mode According to the Speaker Layout

 

Started

 

The signals output from the AVR-890’s SURR. BACK/AMP ASSIGN speaker terminals can be

 

switched to signals of the surround mode being used (vpage 27 “Amp Assign”).

 

 

 

 

Connections

 

 

 

 

 

 

 

 

 

Amp assign mode
SURR. BACK/AMP ASSIGN
Example of speaker installation

 

 

(vpage 27)
Speaker connections

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Settings

Normal

Surround back

 

 

 

 

 

speakers

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Playback

 

 

 

 

 

 

 

 

 

 

 

(7.1)

 

 

 

 

 

 

 

 

 

 

Surround back

 

 

 

 

 

-Multi

 

speakers

 

 

 

 

 

Normal

b Connect to the “L” speaker

 

 

 

 

terminal.

 

 

 

 

 

Zone

 

 

 

 

 

 

 

b Set “S.Back” (vpage 28)

 

 

 

 

 

to “1spkr”.

 

 

 

 

 

 

 

 

 

 

 

 

 

Remote

 

 

 

(6.1)

 

 

 

 

 

 

 

 

 

 

Not connected

 

 

 

 

 

Control

 

 

 

 

 

 

Normal

b Set the “S.Back”

setting

 

 

 

 

(vpage 28) to “None”.

 

 

 

 

 

 

 

 

 

Information

 

 

 

 

 

 

 

 

 

 

 

(5.1)

 

 

 

 

 

 

 

 

 

 

Front Height

 

 

 

 

 

Troubleshooting

Front Height

 

 

 

 

 

speakers

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(7.1)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Connecting the Speakers
Subwoofer with

Front speakers

Front speakers

Center

Surround

built-in amplifier

A

B

speaker

speakers

(L)

(R)

(L)

(R)

(L)

(R)

w q

 

 

 

 

 

 

w

q w q

w q

w q

w

q w q

*/

 

 

 

 

 

 

 

 

For connections of the SURR. BACK/AMP ASSIGN speaker terminals, see “Amp Assign” (vpage 27).

Protection circuit

 

 

Front A or B

 

 

 

 

 

Specifications

Front A Bi-Amp

speakers

 

 

 

 

 

b For connections, see

 

 

 

 

 

or

 

 

 

 

 

“About bi-amp connections”

 

 

 

 

 

Front B Bi-Amp

 

 

 

 

 

(vpage 12).

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(5.1)

 

 

 

 

 

 

 

 

 

 

 

 

 

MAIN ZONE

ZONE2

 

ZONE2

ZONE2

 

 

 

 

 

 

(Default)

speakers

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(2)

 

 

 

 

(5.1)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

If the core wires touch the rear panel and the screws etc., or the ± sides touch each other, the protection circuit will be activated and the power indicator will flash red at intervals of 0.5 secs.

If the protection circuit is activated, the speaker output is isolated, and the power supply goes to the standby state. If the power supply is turned off, after the power supply cord is withdrawn, please confirm that speaker cable and input cable are connected.

Also, if replaying large sound levels by using a speaker having an impedance less than that

specified (eg, 4 Ω/ohms), the temperature will rise, and the protection circuit might be activated. The power supply will go into the standby state, and the power indicator will flash red at 2 second intervals. In this case, please switch off the power supply, and wait until the AVR-890 has cooled down, and the surrounding ventilation is good.

Even if there are no problems with the surrounding ventilation and connections, in the event of the protection circuit becoming activated, due to thinking that the AVR-890 has failed, please contact DENON Service center after switching off.

11