GAudioH
Symptom | Cause/Solution | Page |
Audio is not output. | • Check the connections for all devices. | C 3, |
|
| 8, 10, 11, |
| • Check the speaker connections and configurations. | 12, 15 |
| C 6, | |
|
| 41, 42, |
| • Check whether the audio device power is turned on. | 43, 45 |
| – | |
| • Adjust the master volume. | 20, 52 |
| • Cancel the mute mode. | 20, 52 |
| • Select a suitable input source. | 19, 52 |
| • Select a suitable input mode. | 80 |
No sound is | • Check if the surround output terminals are connected to the | – |
produced from | power amplifier and speakers. |
|
surround speaker. |
|
|
No sound is | • Check if “Amp Assign” is set appropriately in order to output | 65 |
produced from | audio from the surround back terminals. |
|
surround back | • Set “Speaker Config.” – “S.Back” on the menu to something | 65 |
speaker. | other than “None”. |
|
| • Set “Surr.Parameter” – “S.Back” on the menu to something | 61 |
| other than “OFF”. |
|
| • Set the surround mode to something other than “STEREO” and | 33 |
| “VIRTUAL”. |
|
No sound is | • Set “Surr.Parameter” – “PLgz Height” on the menu to “ON”. | 61 |
produced from front | • Check if “Amp Assign” is set appropriately in order to output | 65 |
height speaker. | audio from the front height speakers. | 66 |
| • Set “Speaker Config.” – “F.Height” on the menu to something | |
| other than “None”. |
|
No sound is | • Check the subwoofer connections. | C 6, |
produced from |
| 41, 42, |
subwoofer. | • Turn on the subwoofer’s power. | 43, 45 |
| – | |
| • Set “Speaker Config.” – “Subwoofer” on the menu to “Yes”. | 65 |
| • If “Front” and “Center” for “Speaker Config.” are set to “Large”, | 65, 66 |
| and “Subwoofer Mode” is set to “LFE”, no sound may be output |
|
| from the subwoofers, depending on the input signal or selected |
|
| surround mode. |
|
DTS sound is not | • Set “Decode Mode” on the menu to “Auto” or “DTS”. | 80 |
output. |
|
|
Symptom | Cause/Solution | Page |
Dolby TrueHD, DTS- | • Make HDMI connections. | 8 |
HD, Dolby Digital |
|
|
Plus audio is not |
|
|
output. |
|
|
Dolby PLg mode or | • Check that “Speaker Config.” – “Center” or “Surround” is set | 65 |
DTS NEO:6 mode | to other than “None”. If the speaker system is 2.0/2.1ch, this |
|
cannot be selected. | surround mode cannot be selected. |
|
| • When headphones are used, Dolby PLg or DTS NEO:6 cannot be | – |
| selected. |
|
RESTORER cannot | • Check that an analog signal or PCM signal (fs=44.1/48 kHz) is | 62 |
be selected. | input. For playback of multichannel signals such as Dolby Digital |
|
| or DTS surround, RESTORER cannot be used. |
|
| • Switch the surround mode to other than “DIRECT” or “PURE | 33 |
| DIRECT”. |
|
GControl dock for iPodH |
| |
Symptom | Cause/Solution | Page |
iPod cannot be | • Check the iPod connections. | 12 |
played. | • Insert the AC adaptor of the iPod control dock into the power | – |
| outlet. |
|
| • Switch the input source to “DOCK”. | 19 |
version Basic
version Advanced
Information
BD | 126 |