ENGLISH
(2) Rear Panel
qANALOG OUT (BALANCED) connectors
•These are active balanced outputs using XLR type connectors.
•Connect these connectors to the balanced analog input connectors on an amplifier or console.
•Pin layout: 1. Common
2.Hot
3.Cold
•Applicable connector: Cannon
common pin.
wANALOG OUT (UNBALANCED) jacks
•These are unbalanced outputs using RCA type jacks.
•Connect these jacks to the unbalanced analog input jacks on an amplifier or console.
eLEVEL L/R controls
•Use these controls to adjust the level of the audio signals from the ANALOG OUT (BALANCED) connectors.
rREMOTE connector
•This is a parallel remote connector. Use it to control the
•Applicable connector:
•Connector signal layout:
Pin No. | Signal name | I/O |
|
|
|
|
|
1 | FG | – |
|
14 | PLAY tally | O | TTL (lol = 20 mA) |
2 | PLAY command | I | HCMOS (li = 3 mA) |
15 | PAUSE tally | O | TTL (lol = 20 mA) |
3 | PAUSE command | I | HCMOS (li = 3 mA) |
16 | CUE tally | O | TTL (lol = 20 mA) |
4 | CUE command | I | HCMOS (li = 3 mA) |
17 | INDEX 2/INDEX 3 tally | O | TTL (lol = 20 mA) |
5 | TRACK (+) command | I | HCMOS (li = 3 mA) |
18 | Tally common | – |
|
6 | TRACK | I | HCMOS (li = 3 mA) |
19 | Reserved | – |
|
7 | SEARCH (FWD) command | I | HCMOS (li = 3 mA) |
20 | Reserved | – |
|
8 | SEARCH (REV) command | I | HCMOS (li = 3 mA) |
21 | Reserved | – |
|
9 | FADER START command | I | PHOTO COUPLER |
22 | Tally power supply | – | +5 V, 20 mA |
10 | Command common | – | (li =10 mA) |
23 | Command common | – |
|
11 | NC | – |
|
24 | EOM tally | O | TTL (lol = 20 mA) |
12 | Reserved | – |
|
25 | Reserved | – |
|
13 | Reserved | – |
|
|
|
|
|
NOTE: The tally output pin has open collector IC specifications (Imax. 20 mA, Vmax. 5 V), but the maximum supply current is 80 mA, so use with a total load current of 80 mA or less.
tDIGITAL OUT jack
•This is an unbalanced output using an RCA type jack.
•Connect this jack to the unbalanced digital input jack on an amplifier or console.
•Signal format: Selectable (See Page 22, 9))
(3) Display Window
qREPEAT indicator
• This lights when the repeat mode is set.
wTime mode indicators
•“ELAPSED” lights when the elapsed time is displayed.
•“REMAIN” lights when the remaining time is displayed.
ePlay mode indicators
•“SINGLE” lights when in the single track play mode.
•“TOTAL” lights when in the continuous play mode.
rTrack no. display
•This indicates the track number at the current position. The track number lights during the track search operation and when switching to the standby mode.
•If the next track is scheduled, that track number flashes on the track no. display.
tPlay pause indicator
yPlay indicator
uIndex no. display
•Normally “Tr” is displayed. In the index search mode, the index number is displayed. If the next index is scheduled, that index number flashes on the index no. display. The index number also lights during the index search operation.
iPlaying position display
•This indicates the current position within the track’s total playing time.
oPitch display
• This indicates the set play speed in %.
!0 Program indicator
•This lights when a program is input.
•This flashes when the PROG. IN mode is set.
!1 20 tracks music calendar
•In the single track play mode, only the specified track lights.
•In the continuous play mode, everything from the specified track to the last track lights.
•Track numbers are displayed up to track 20. Tracks 21 and on are not displayed.
!2 Playing time display
•This indicates the time of the current position, in minutes (m), seconds (s) and frames (f).
!3 Character display
•This displays operation messages in the preset and program modes.
10