ENGLISH

3PART NAMES AND FUNCTIONS

(1) Front panelqPOWER button (¢ON £OFF)

• Push this button to turn power on and off.

CAUTION:

Do not turn off the power while a disc is loading or being ejected. Otherwise loading mechanism may be damaged.

wPOWER indicator

• This lights when the power is on.

eDisc loading slot

Load the disc slowly, and release it once the DN-D6000 starts grabbing the disc in.

NOTE:

Please clean the dirt of the label side of a disc and start loading of the disc.

The dirt causes a slip of a disc loader roller.

CAUTIONS:

Do not load discs when the power is turned off.

Do not try to forcibly remove a disc once the DN-D6000 has started to grab the disc.

Do not load more than once disc at a time or insert anything other than discs.

Otherwise loading mechanism may be damaged.

(2) Rear panelyAnalog output jacks (LINE OUT)

This is unbalanced RCA output jacks.

Audio signals outputs.

uFader start jack

Use this when your mixer has Fader Start function with 3.5 mm stereo mini cord.

iDigital output jack

Digital data is available from this jack.

Use 75 /ohms pin cord for connection.

We recommend you use braided wire type shielded cable.

NOTE: The playback level after analog conversion is set to -12dB bellow the usual level to avoid digital distortion.

oRemote connector (REMOTE)

Connect this connector to the RC-D60 using the included cord.

(3) RC-D60 Front panel

CAUTION:

Note that there are many buttons working two different function selected by short time pushing or long pushing (1second or more). The mark indicates short time push function and mark indicates long time push function.

!0PLAY/PAUSE button (13)

This button will start or pause playback.

Push once to start playback, once again to pause playback, and once more to resume playback.

!1CUE button

Pushing this button in play mode will force the track back to the position which playback started. While in search mode, it makes new Cue point. (Cue)

In Cue mode, by pushing the CUE button makes a Stutter sound from the Cue point. This is called Stutter play. (Stutter)

!2Scratch Disc

Use this vinyl scratch disc for scan, manual search, Pitch Bend and Scratch operations.

!3FLIP/CLR button

FLIP:

 

Use this to select operating mode of A1 and A2

 

buttons, from Hot Start mode and Stutter

 

mode. The display will indicate “H/S” or “STR”

A1, A2 CLR:

!5A1, A2 button

Using this button you can create starting point for Hot Start, Seamless Loop and Stutter.

!6SAMP button

Push this button to record or play sound of Sampler.

!7B button

Use this to set the B point for to create a Seamless Loop after the A point has been set.

!8(SAMP) B button

• Use this to set the Sampler loop B point.

!9EXIT/RELOOP button

Use this to exit or return back again to Seamless loop playback. You can add variety to looping with this function.

@0(SAMP)EXIT/RELOOP

Use this to turn the Sampler Loop mode on and off. Also acts as EXIT/RELOOP button for Sampler Loop to exit or back again.

@1NEXT TR./B TRIM button

When the button is pressed during playback, the NEXT TRACK MODE is selected. If the button is pressed again, the B TRIM MODE is selected.

In the standby and pause modes, only the B TRIM MODE can be selected.

rDisc slot LED

This flashes while the disc is ejecting.

The LED lights when the disc is not loaded and serves as the disc slot illumination.

tDISC EJECT button

Push this button to eject the disc.

The disc will not eject during playback. Stop playback before pushing this button.

If the A1 or A2 button is pushed while pushing

the FLIP button, you can clear the selected A

point.

By holding down just the FLIP button for more

than 1 sec, you can clear A1 and A2 points all

at once.

!4(SAMP) RVS/CLR button

(SAMP)RVS:

Use this to select the sample play direction forward and reverse. When select reverse RVS LED lights up.

(SAMP) CLR:

If the SAMP button is pushed while pushing the this button, you can clear the SAMP data. Or, by holding down just the this button for more than 1 sec.

@2(SAMP.) STOP button

Push this button while in Sampler record or playback, Sampler record or playback stops.

@3TITLE button

CD TEXT:

When there is CD text data, the CD text data is displayed automatically or when the button is pressed.

If no TEXT is available, the display will indicate “No TEXT”.

MP3:

When an MP3 file has ID-3 tag data, the title, artist name and album name are selected and displayed each time the button is pressed.

8