Desa DVFH34P Optional Remote Operation, Operating Optional GWMS2 Wall Mounted Switch

DVFH34, DVFH34P

DIRECT-VENT FIREPLACE (NATURAL/PROPANE/LP)

OPERATING

FIREPLACE

Continued

OPTIONAL REMOTE

OPERATION

Note: All remote control accessories must be purchased separately (see Accessories, pages 36 and 37). Follow instructions in- cluded with the remote control.

Thermostat Control Operation

(Optional GHRCTA Series Only) The thermostat control setting on the remote control unit can be set to any comfort level between WARMER and COOLER. The burners will turn on and off auto- matically to maintain the comfort level you select. The ideal comfort setting will vary by household depending upon the amount of space to be heated, the output

GHRC Series Operation:

2a. Press the ON/OFF button to turn the burners on and off. When turning burners off, the pilot will remain lit.

GHRCTA Series Operation:

2b. Press the AUTO/ON/OFF button on the hand-held remote control (see Fig- ure 58). The lights to the left of the button will show AUTO, ON, or OFF.

•In the ON mode, the burners will ignite. The heater is in manual mode when ON is lit.

•In the AUTO mode, the thermostat in the hand-held remote unit con- trols the room temperature. To in- crease the room temperature, press the top arrow of the TEMP button. To lower the room temperature, press the bottom arrow of the TEMP button. At higher settings the heater will run longer.

IMPORTANT: This remote control has been specially engineered to take an air temperature sample ev- ery minute in the auto mode. It will not respond immediately to the temperature setting being turned up or down.

IMPORTANT: The hand-held re- mote control unit must be near the heater. Do not keep the hand-held remote control unit too close to the heater. The thermostat on the hand-held remote control unit will heat up too quickly and turn the heater off.

3.To turn the burner off, press the AUTO/ON/OFF button until OFF lights. The pilot will remain lit.

IMPORTANT: To turn the pilot off, manually turn the control knob on the heater to the OFF position.

of the central heating system, etc.

NOTICE: You must light the pilot before using the hand-held re- mote control unit. See Lighting

Blower Control Knob	Variable
(Optional Accessory)	Control Knob

OPERATING

OPTIONAL GWMS2

WALL MOUNTED

SWITCH

Instructions on page 25.

1. After lighting, let pilot flame burn for

about one minute. Turn gas control

knob to ON position. Adjust variable

control knob anywhere between HI

and LO. Slide the selector switch to

the REMOTE position (see Figure

OFF

ON

REMOTE

OFF

ON

Selector Switch in Remote Position

N		L
O		O
T	F	O
O	F
LIP

Gas Control

Knob in ON

Position

I H

Make sure the heater switch is on AUTO. This wall switch works just like the con- ventional light switch. Flip the switch up for on and down for off.

Note: Make sure that this switch is not in a position to be mistaken for a light switch. This may result in the heater being inad- vertently turned on without the proper

57). Note: The burners may light if

hand-held remote ON button was on

when selector switch was last turned

off. You can now turn the burners on

and off with the hand-held remote

control unit.

IMPORTANT: Do not leave the selec-

tor switch in the REMOTE position

when the pilot is not lit. This will

drain the battery.

IMPORTANT: Be sure to press the

ON/OFF buttons on the hand-held

remote control unit for up to 3 sec-

onds to assure proper operation.

Figure 57 - Setting the Selector Switch, Gas Control Knob, and Variable Control Knob for Remote Operation

Shows Temperature

Setting

The Log Heater will Automatically Cycle between Pilot and the Heat Setting that has been Selected

precautions being taken. See installation instructions on page 22 of this manual.

Increases Room

Temperature in AUTO

Mode

Decreases Room

Temperature in AUTO

Mode

Turns Burners On or Off and Allows You to Choose the Auto Setting

Figure 58 - Thermostat Hand-Held Remote Control Unit Selections (GHRCTA Series Only)

26 106394