Manuals / Desa / Household Appliance / Gas Heater

Desa BG30P, GG30NT, FG30PT, FG30NT, RG30NT, RG30P, GG30PT Installing Bottom Mounting Screws

Models: GG30PT BG30N FG30NT RG30N GG30NT FG30P GG30N GG30P FG30PT FG30N RG30NT BG30PT RG30P BG30NT BG30P

1 32

Download 32 pages 51.75 Kb

Page 11

INSTALLATION

Continued

Installing Bottom Mounting Screws

1.Locate two bottom mounting holes. These holes are near bottom on back panel of heater (see Figure 12).

2.Mark screw locations on wall.

3.Remove heater from mounting bracket.

4.If installing bottom mounting screws into hollow or solid wall, install wall anchors. Follow steps 1 through 4 under Attaching To Wall Anchor Method, page 10.

If installing bottom mounting screw into wall stud, drill holes at marked locations using 9/64" drill bit.

5.Replace heater onto mounting bracket.

6.Place spacers between bottom mounting holes and wall anchor or drilled hole.

7.Hold spacer in place with one hand. With other hand, insert mounting screw through bottom mounting hole and spacer. Place tip of screw in opening of wall anchor or drilled hole.

8.Tighten both screws until heater is ﬁrmly secured to wall. Do not over tighten.

Note: Do not replace front panel at this time. Replace front panel after making gas connec- tions and checking for leaks (see pages 12 through 14).

Front View

Heater	Wall
	Wall
	Spacer

Side View

Figure 12 - Installing Bottom Mounting

Screws

114683-01B

www.desatech.com

11

Image 11

Desa GG30NT, FG30PT, FG30NT, RG30NT, RG30P, GG30PT, BG30NT, BG30PT Installing Bottom Mounting Screws

Contents

What to do if YOU Smell GAS Table of Contents Poisoning may lead to death Safety Information Unpacking Product FeaturesLocal Codes Unusually Tight Construction AIR for Combustion VentilationProviding Adequate Ventilation Following are excerpts from National Fuel Determining if You Have a Conﬁned or Unconﬁned Space Determining FRESH-AIR Flow for Heater Location Ventilation Air From Inside Building InstallationVentilation AIR Check GAS Type Locating Heater Installation Items Removing Front Panel Of Heater Installing Heater to WallThermostat Sensing Bulb Thermostat Models Only Mounting Bracket Placing Heater On Mounting Bracket Attaching To Wall Anchor Method Installing Bottom Mounting Screws Installing Bottom Mounting Screws Typical Inlet Pipe Diameter Connecting to GAS Supply Equipment Checking GAS ConnectionsTest Pressures Equal To or Less Than Psig 3.5 kPa Make sure control knob of heater is in the OFF position Open equipment shutoff valve see , Lighting Instructions Manual Control Models For Your Safety Read Before LightingOperating Heater Shutting Off Burner Only pilot stays lit Manual Lighting ProcedureTo Turn OFF GAS To Appliance Shutting Off Heater Thermostat Control Operation Check pilot ﬂame pattern and burner ﬂame pat- tern often Inspecting HeaterPilot Flame Pattern Burner Flame Pattern Cabinet Cleaning MaintenanceODS/PILOT and Burner Burner Pilot AIR Inlet Observed Problem Possible Cause Remedy Troubleshooting Burner oriﬁce is clogged Clean burner see Cleaning Out when control knob is re Control knob not pressedSafety interlock system has Delayed ignition of burner Manifold pressure is too low Air passageways on heater Or shut off Qualiﬁed service personOperation Processes Hours of operation Turning control knob to Statement above Gas leak. See Warning BG30P, FG30P, GG30P, RG30P, GMG30P SpecificationsBG30N, FG30N, GG30N, RG30N, GMG30N Parts Under Warranty Service HintsTechnical Service Service Publications Replacement Parts Illustrated Parts Breakdown NJF 8C Parts List Illustrated Parts Breakdown NJF 8C For all models. Equipment shutoff valve with 1/8 NPT tap AccessoriesEquipment Shutoff Valve GA5010 FAN Kits GA3250T Parts Centrals Limited Warranty VENT-FREE Residential GAS Heaters Warranty InformationKeep this Warranty