HOW TO RAISE THE TABLE

To raise the feed table, turn the handwheel (A) Fig. 15 counter- clockwise. To lower the feed table, turn hand-wheel clockwise.

NOTE: Each 1/4 turn of handwheel (A) increases or decreases the height of the table by 1/64".

Fig. 15

A

HOW TO CHECK AND ADJUST THE FEED BELT TRACKING AND TENSION

IMPORTANT: Read this complete section before making any adjustments to belt tracking or tension.

TO CHECK AND ADJUST TRACKING

Disconnect the machine from the power source.

IMPORTANT: Since the feed belt runs slowly, the response time to any adjustment may also be slow. Take your time.

1.The tracking and tension of the feed belt was set at the factory. Before making any adjustments, place a reference mark on the table on either side of the belt with a pencil. Turn the feed/speed knob (E) Fig. 16 "ON" and adjust to the maximum speed. Let the belt run. Observe the tracking direction. You will not need to adjust the belt If it does not make any measurable side movement in five minutes.

NOTE: A new belt will usually be tighter on one side than the other. Frequent adjustments are normal for the first few hours due to belt stretch. Adjustments to belt tracking can also affect belt tension.

Fig. 17 shows a close-up of the right set screw (B).

2.If the belt (F) tracks to the right, turn the right set screw (B) Fig. 17 clockwise 1/4 turn or less with the provided 1/8" T-handle hex wrench.

3.If the belt (F) tracks to the left, turn the right set screw (B) Fig. 17 counter-clockwise 1/4 turn or less with the provided 1/8" T-handle hex wrench.

NOTE: Adjust one side and let the movement stabilize before adjusting again. Continue to tighten or loosen this

adjustment until the feed belt tracks properly.

TO CHECK AND ADJUST TENSION

If the belt slips on the rear drive roller during sanding operations, adjust the belt tension.

To adjust, turn both set screws (A) and (B) Fig. 16 clockwise in 1/4 turn increments.

NOTE: When adjusting the belt tension, turn both set screws the same amount. DO NOT over-tighten the belt. Excessive tension will cause premature belt wear, bearing wear, and will overload the motor. Listen for motor load speed changes when adjusting the belt tension.

NOTE: Adjustments to belt tension can affect belt tracking. Frequent adjustments are normal for the first few hours.

E

A F

Fig. 16

B

B

Fig. 17

10

Page 9 Page 11
Page 10
Image 10
DeWalt 31-260X instruction manual HOW to Raise the Table, HOW to Check and Adjust the Feed Belt Tracking and Tension
Page 9 Page 11

31-260X specifications

The DeWalt 31-260X is a powerful and versatile cordless drill that stands out in the competitive world of power tools. With its combination of robust performance, advanced features, and user-friendly design, it has become a favorite among both professionals and DIY enthusiasts alike.

One of the main features of the DeWalt 31-260X is its high-performance motor, which delivers impressive torque and speed to tackle a variety of materials and applications. The drill operates at multiple speed settings, allowing users to adjust the RPM according to their specific project needs. This feature is particularly useful when working with different materials, such as wood, metal, or plastic, ensuring optimal results with minimal effort.

The 31-260X also boasts a compact and lightweight design, making it easy to maneuver in tight spaces and reducing user fatigue during extended use. The ergonomic grip is designed for comfort and control, providing a secure hold that enhances precision during drilling and driving tasks.

In terms of battery technology, the DeWalt 31-260X is equipped with the brand's state-of-the-art lithium-ion batteries, which deliver extended run times and shorter charge times. This ensures that users can work for longer periods without interruptions, and when it is time to recharge, the batteries are ready to go in no time. Additionally, the drill features an integrated battery level indicator, allowing users to monitor the remaining power at a glance.

Another standout characteristic of the DeWalt 31-260X is its durable construction. Built to withstand the rigors of job site conditions, the drill features a rugged housing that protects internal components from dust and debris. This durability enhances its lifespan, making it a smart investment for those who rely on their tools day in and day out.

To further enhance its versatility, the 31-260X is compatible with a wide range of accessories, including drill bits and driving attachments, catering to various tasks with ease. With a quick-release chuck, users can effortlessly switch between different bits, maximizing productivity on the job.

In summary, the DeWalt 31-260X is a standout cordless drill that combines power, efficiency, and durability. Its impressive motor performance, user-friendly design, and advanced battery technology make it an invaluable tool for anyone looking to complete projects with precision and ease. Whether for professional use or home improvement tasks, the DeWalt 31-260X is a reliable choice that won’t disappoint.
Top Page Image Contents