Manuals / Diamond Systems / Computer Equipment / Computer Hardware

Diamond Systems PR-Z32-EA-ST, PR-Z32-E-ST user manual 28.PC/104 Mechanical Drawing

Models: PR-Z32-E-ST PR-Z32-EA-ST

1 74

Download 74 pages 11.09 Kb

Page 74

28.PC/104 MECHANICAL DRAWING

The following drawing is from the PC/104 specification. This document may be downloaded from www.pc104.org or from www.diamondsystems.com/support/techliterature.

Prometheus CPU User Manual V1.44

Page 74

Image 74

Diamond Systems PR-Z32-EA-ST, PR-Z32-E-ST user manual 28.PC/104 Mechanical Drawing

Contents

Prometheus Table of Contents 22.2 22.4Description CPUProcessor Section FeaturesSystem Features Analog Output Counter/TimersAnalog Input Digital I/OPrometheus Board Drawing Cable a Main I/O Connector J3O Headers Cable BLPT1 Connector Part NumbersCOM1 COM4 IR RX, IR TXInput Power J11 USB J5 Output Power J12Ethernet J4 Auxiliary Serial Port Connector J15 Watchdog/Failsafe Features J6Floppy Drive J7 IDE Drive J8Data Acquisition I/O Connector J14 Model PR-Z32-EA only Signal Name Definition11 PC/104 Bus Connectors J2 PC/104 16-bit bus connector J1 PC/104 8-bit bus connectorCmos RAM Jumper ConfigurationJ10 System Configuration J6 Watchdog Timer & System Recovery CPU Chip Selects System FeaturesSystem Resources Console Redirection to a Serial Port Watchdog Timer System Reset Failsafe Mode / Bios RecoveryBackup Battery Flash MemoryDOS BiosBios Settings Bios Download / Recovery Operating System Formatting Initial SetupDisk-On-Board Flash File Storage Known Limitations Life Cycle Management and CalculationsSystem I/O EthernetSerial Ports Parallel PortBooting to DOS From a Floppy Drive Installing an OS From a Floppy Drive onto a Flashdisk ModuleInstalling an OS from a Hard Disk onto a Flashdisk Module Data Acquisition Circuit Base + Write Function Read Function Data Acquisition Circuitry I/O MAPBase Address LSBData Acquisition Circuit Register Map AD7 AD6 AD5 AD4 AD3 AD2 AD1 AD0Base + Command RegisterRegister Bit Definitions Base + Write Not Used Read Base + ReadValue = Base + 0 value + Base + 1 value AD9 AD8Base + Read/Write Channel Register Base + Write Analog Input Gain Base + Read Analog Input Status STS Wait Dacbsy OVF ScanenBase + Read/Write Fifo Threshold Base + Read/Write Interrupt / DMA / Counter ControlCKSEL1 CKFRQ1 CKFRQ0 Adclk Dmaen Tinte Dinte Ainte FT5 FT4 FT3 FT2 FT1 FT0Base + Read Channel and Fifo Status Base + WriteDA7 DA6 DA5 DA4 DA3 DA2 DA1 DA0 FD5 FD4 FD3 FD2 FD1 FD0DA9 DA8 Base + Write DAC MSB + Channel NoDACH1 DACH0 Base + Read Analog Operation StatusDioctr Dira Dirch Dirb Dircl Base + Read / WriteBase + Read / Write Digital I/O Control Register Dioctr =Base + Read/Write Counter/Timer D23 Base + Read/Write Counter/Timer D7Base + Read/Write Counter/Timer D15 Base + Write Counter/Timer Control Register Ctrno Latch Gtdis Gten Ctdis Cten Load CLRBase + Read Fpga Revision Code REV7 REV6 REV5 REV4 REV3 REV2 REV1 REV0Data Acquisition Circuit Configuration Unipolar / Bipolar Inputs Analog Output ConfigurationSingle-ended / Differential Inputs Overview Analog Input Ranges and ResolutionInput Range Resolution 1 LSB Input Range SelectionPerforming AN A/D Conversion Perform an A/D conversion on the current channel LSB = inpbase MSB = inpbase+1Input voltage = A/D value / 32768 * Full-scale input range 15.A/D SCAN, INTERRUPT, and Fifo Operation Ainte Scanen Prometheus A/D Operating ModesLOW, High Description Analog Output Ranges and ResolutionResolution LSB = Output voltage range16.4 D/A Conversion Formulas and Tables REF 1 LSBConversion Formulas for Bipolar Output Ranges Generating AN Analog Output 18.2 A/D unipolar offset Analog Circuit Calibration18.1 A/D bipolar offset 18.3 A/D full-scaleDigital I/O Operation Counter 1 Counting/Totalizing Functions COUNTER/TIMER OperationCounter 0 A/D Sample Control Command Sequences CounterCounter Outpbase+15,0x01 Outpbase+15,0x81 Data Acquisition Specifications Power Supply ConfigurationUsing the Flashdisk with Another IDE Drive Flashdisk Module23. I/O Panel Board Location Type Description Panel Board I/O ConnectorsPanel Board Top Side / External Use I/O Connectors USB aPanel Board Power Connections J12 pinout to/from DC/DC power supplyJ3 Pinout J9 Pinout Installation J5 USBFlash Disk Programmer Board Cable Kit C-PRZ-KIT 25.I/O CablesPhoto No Cable No Description PL5 pin no DB15F pin no Signal VGA Accessory BoardPL5 pin no PL5 Signal J25 pin no J25 Signal Links Prometheus Connector Manufacturer Manufacturer Part NoMounting Prometheus on a Baseboard Website informationPage 28.PC/104 Mechanical Drawing