Manuals / Digital Data Communications / Photography / Security Camera

Digital Data Communications FCS-4100, FCS-4500, FCS-4300 Camera installation, ‹ ID address setup

Models: FCS-4100 FCS-4000 FCS-4300

1 93

Download 93 pages 27.18 Kb

Page 10

Camera installation

Camera installation

Before installation, please set for the communication protocol, baud rate and camera ID address first.

ID address setup

There are 8 dip-switchers on the PCB board. Please set it up as below: All the dip-switchers are OFF.

*Remarks: Please reboot the camera after the camera setup is done.

Image 10

Digital Data Communications FCS-4100, FCS-4500, FCS-4300, FCS-4400, FCS-4200, FCS-4000 Camera installation, ‹ ID address setup

Contents

User Manual LevelOneVer2.1.0-0804 Before You Use This Product 1. All operation please refer to the instruction 2. Please don’t place the product on unstable desk or bracketTable of Contents GNU GENERAL PUBLIC LICENSEFunctions and Operation directory Package ContentsPreset position set up and recall Pan/Tilt/ZoomUsers can press the zoom button to adjust the image viewing distance ‹ Focusing control‹ Iris control Installation Notice Hardware InstallationFCS-4300/4400/4500Housing installation FCS-4000/4100/4200Housing installation ‹ unscrew the bottom screw to install cables ‹ For the alarm cable‹ ID address setup Camera installationRemarks Please reboot the camera after the camera setup is done ‹ Alarm Dip-switchers ‹ Protocol setupRemarks Please reboot the camera after the protocol setup is done ‹ Aim the camera plug to the bottom socket to connectingBracket installation ‹ CAS-4000B ceiling mount kit Fixed the iron tube to the cover of power boxTurn the screw to tighten the brackets and power box ‹ CAS-4000C corner mount kitFixed the bracket on the rear of power box The assembly completed ‹ CAS-4000D pole mount kitThe assembly will be done after the stainless ring is hooped Software Installation Install “IP CamLocator”Install “IP CamSecure” Click”Install Software” Custom Setup Type Main Menu How to Use IP CamLocatorConfiguration of Main Console Initial use IP Cam LocatorAbout Main Menu CameraUser CameraSetup Page Page Page Page DDNS settings You can change the DDNS settings here Apply settings Click on “Apply” to use the new settings Upgrade Factory Default Reboot Click on “OK” to continue. The device will automatically rebootUser Note Configuration file format is *.conf Page Info User Mode：Set a user to Admin, Operator or Viewer modeUsername：Set a user name between 5 and 16 characters Date/Time Note： DNS SettingTCP/IP IP AddressPage PPPoE DDNS Note：About Note：How to Access to the Network Camera Initial accessing the network cameraSetting Configuration of Main Console LanguageClient Setting Image Setup Pan / Tilt control Digital Zoom in / out the image via the monitor window Live ViewNote：：Pause the current video ：Stop the current video cameras via the Ethernet using your microphone. Video play buttons：Play the video ：Record the current video System Basic SettingInformation Day & Time InitializePage General CameraNote： MPEG4 Computer View Note：Multicast streaming RTSP If RTSP mode is ONRTP If RTSP mode is ON Unicast streaming Multicast address Specify the multicast server addressMobile View Image Size The Image size of Mobile view is fixed at 11000. Specify an even number from 1024 toTime-To-Live Set the maximum TTL that multicast can pass through QualityMJPEG Note：Information NetworkNote： follows PPPoE DDNS UPnP IP Notification Page Security AccountHTTPS PTZ Control AdvanceSetting Setting Preset PositionSet：Use it to save the camera position to a preset number preset position setting General PatrolTour position 4. Follow the steps to set the other orders 3. Click the SET. The tour position is saved5. Click the OK to save the tour General FTP ClientAlarm sending Note：Suffix：Select a suffix to add to the file name Note：Periodical sending General SMTPNote： followings Attached File Type Select to attach the file as JPEG or MPEG4Alarm sending the Alarm Buffer - Alarm buffer setting Menu on page HTTP Event Periodical sendingsensor input or with the built-in motion detection function to HTTP server. HTTP client setting menu is composed of two tabs, General and Alarm sending GeneralAlarm sending Note：Schedule SettingAlarm Input SettingAlarm Buffer SettingMotion Detection A detecting zone 1 appears and use mouse to adjust and move the zone boundaries and position. Use tool bar to set Threshold and Sensitivity value Note：System Log system after power on Trouble shooting sheetSolutions TroublesTechnical Parameters 1/4 Exview HAD CCDGNU GENERAL PUBLIC LICENSE PreambleGNU GENERAL PUBLIC LICENSE Terms And Conditions For Copying, Distribution And ModificationPage Page Page NO WARRANTY REPAIR OR CORRECTION