DMP Electronics XR2500F manual Wiring Diagram, Use Marking

Introduction

2.6Wiring Diagram

The XR2500F system below shows the component layout. The wires shown in this guide have been factory installed and connected. The dashed lines represent wires running underneath or behind a component. Detailed wiring diagrams for each supplied component appear in following sections of this guide.

				WARNING
THIS UNIT MAY BE PROGRAMMED TO USE AN ALARM VERIFICATION FEATURE THAT RESULTS IN DELAY OF THE						Verification Control Unit		Smoke	Detector
SYSTEM ALARM SIGNAL FROM THE INDICATED CIRCUITS. THE TOTAL DELAY (CONTROL UNIT PLUS SMOKE
						Zones	Delay	Model	Delay
DETECTORS) SHALL NOT EXCEED 60 SECONDS. NO OTHER SMOKE DETECTOR SHALL BE CONNECTED TO THESE
CIRCUITS UNLESS APPROVED BY THE LOCAL AUTHORITY HAVING JURISDICTION (AHJ).							Zones 9, 10, and all expanded
							zones are suitable for Class B
							(as applicable for the initiating
			S				and signaling line circuits per
Use Marking			S				ANSI/UL 864 Table 48.2 or
Commercial and Residential			BLACK WHITE	S			48.3). Installation limits under
							local Authority Having
Fire, Burglar, Holdup, and
							Jurisdiction (AHJ).
Access Protected Premise Unit
		GREEN		866	866
	GREEN/	BLACK	WHITE	Module	Module		See LT-0759, Two 866
							NAC Modules section for
	YELLOW
Connected to							complete 866 information.
Enclosure Door				56 VA
			16 VAC	Transformer

See LT-0759, 893A	S	S
Dual Phone Line			10K EOL To Notification
		S
	To Telco S
Module section		S	Appliances
for complete 893A		S	10K EOL
information.

TYPES OF SERVICE

Suitable for Mercantile Local and Police Station Connect.

Suitable for Proprietary, PPU, other technologies, local.

Suitable for Signaling and
Remote Station PPU DACT
Service.	J3	J4		XR2500F
Suitable for manual fire alarm,	Line
	Phone
automatic fire alarm, sprinkler		Tamper		Command	Expansion
supervisory, or water flow	Link LED	J1
				Processor™	Slot
alarm.	Power LED	Ethernet			Card
				Panel
Suitable for Standard or	Power				J6
	LED
Encrypted Central Station with	R
NET or CELL communication.		J22
	X
	L
		Output 1 OVC Output 2
Suitable for Household Fire and	Battery		Out2		J16
Household Burglary.	Start	J8		3
				5	Reset
			Out1	4
		PROG		Outputs 3-6

Suitable for Coded and March	AC	AC	+B	–B BELL GND RED YEL GRN BLK SMK GND Z1										GND Z2		Z3 GND Z4			Z5	GND Z6 Z7		GND Z8		Z9+ Z9– Z10+ Z10–				Expansion Zones
Time signaling.	1	2	3	4	5	6	7	8	9	10	11	12	13	14	15	16	17	18	19	20	21 22	23	24	25	26	27	28

NFPA 72				Red	Black
This equipment should be	From XR2500F					To Fire Command Center on enclosure door
installed in accordance with
the National Fire Alarm Code,	panel to 12 VDC.
ANSI/NFPA 72 (National Fire
Protection Association,
Batterymarch Park, Quincy, MA
02269). Printed information
			+		-			+	-
describing proper installation,
		XR2500F Secondary Power Supply
operation, testing,									Two 12 VDC batteries	Refer to LT-0759, Standby
		1 Amp maximum charge current.
maintenance, evacuation									connected in parallel with a
		Use only 12 VDC rechargeable batteries.								Battery Selection section
planning, and repair service is									Model 318 Dual Battery
										for battery standby times and
to be provided with this									Harness. See Secondary
		Replace every 3 to 5 years.								numbers of batteries to use.
equipment.									Power Supply section.
		12 VDC battery					12 VDC battery
											Battery Compartment

Figure 2: XR2500F System

Digital Monitoring Products XR2500F Installation Guide

4