Manuals / Eiki / Computer Equipment / Projector

Eiki EIP-1600T owner manual Reference, Appendix

Models: EIP-1600T

1 69

Page 9

Reference
Appendix
Maintenance	51
Maintenance Indicators	52
Regarding the Lamp	54
Lamp	54
Caution Concerning the Lamp	54
Replacing the Lamp	54
Removing and Installing
the Lamp Unit	55
Resetting the Lamp Timer	56

Connecting Pin Assignments	57
RS-232C Specifications and Command
Settings	58
Computer Compatibility Chart	59
Troubleshooting	60
Specifications	62
Dimensions	63
Index	64

EIP-1600T_EN_b

06.1.24, 1:01 PM

Page 9

Image 9

Eiki EIP-1600T owner manual Reference, Appendix

Contents

OWNER’S MANUAL EIP-1600T06.1.16, 906 AM EIP-1600TENaModel No. EIP-1600T Serial No SPECIAL NOTE FOR USERS IN THE U.KDANGER 06.1.24, 100 PM EIP-1600TENa2. CONSUMER PRODUCT SAFETY ACT 1. WARRANTYENGLISH WARRANTY” CLAUSEINFORMATION Caution Concerning Lamp ReplacementDeclaration of conformity PRODUCT DISPOSALFor Future Reference How to Read this Owner’s ManualPP. 60 and MaintenanceUsing ContentsSetup Useful FeaturesAppendix Reference5. Cleaning IMPORTANT SAFEGUARDS8. Accessories 11. Power Sources19. Replacement Parts 18. Damage Requiring Service20. Safety Check 15. OverloadingCaution concerning the setup of the pro- jector Observe the following safeguards when setting up your projectorCaution concerning the lamp unit Warning about placing the projector in a high positionUsing the projector in other countries InfoTemperature monitor function Caution regarding usage of the projectorAccessories Supplied accessoriesOptional accessory Projector Part Names and FunctionsTop View Front ViewPart Names and Functions Continued Rear ViewTerminals For selecting menu items Using the Kensington Lock on the projectorPart Names and Functions Continued Inserting the Batteries2 Insert the batteries 3 Attach the cover and slide it until it clicks into placeUsable Range Quick Start Setup and Projection1. Place the projector facing a wall or a screen 3. Remove the lens cap and turn the projector on P7. Correct trapezoidal distortion GEOMETRIC ADJUSTMENT PP 6. Adjust the focus, image size, and projector angle PP. 308. Turn the Power off 4. Turn the video equipment on and start playbackSetting up the Projector Setting up the ProjectorStandard Setup Front Projection Ceiling-mount SetupIndication of the Projection Image Size and Projection Distance Projection PRJ ModePicture Screen Size and Projection Distance Setting up the Projector ContinuedWhen using a wide screen 169 and projecting 169 image When using a normal screen 43 and projecting 43 image SIDE BAR ModeWhen using a normal screen 43 and projecting 169 image projector Samples of Cables for ConnectionConnecting to Video Equipment To component output Y, CB/PB, CR/PR terminal DVD, etcTo INPUT1 or INPUT2 terminal Component cable commercially available When connecting to equipment with S-video output terminal INPUT3 Connecting to Video Equipment ContinuedWhen connecting to equipment with video output terminal INPUT4 accessoryTo HDMI output terminal When connecting to equipment with HDMI output teminal INPUT6HDMI compatible device To INPUT6 terminal HDMI cable type A commercially availableaccessory Connecting to a ComputerInfo Controlling the Projector by a ComputerTurning the Projector On/Off Connecting the Power CordTurning the Projector on InfoImage Projection Switching the Input ModeTurning the Power off Putting the Projector into Standby Mode Unplug the power cord from the AC1 Adjusting the Focus Adjusting the Projected Image2 Adjusting the Screen Size 3 Adjusting the Height3 Use the rear adjustment foot to make the projector level Rear adjustment footInfo Correcting Trapezoidal Distortion Image Projection ContinuedThere are the two types of the Keystone Correction Selecting the Type of Correction “GEOMETRIC ADJUSTMENT” will be displayedEach time cKEYSTONE is pressed, the display toggles as follows Repeat the same procedure with GEOMETRIC ADJUSTMENTImage Projection Continued 4 Press i ENTER to set the posi- tionon the remote control and the H & V KEYSTONEPress cKEYSTONE or iENTER “H&V KEYSTONE” mode endsPress RESIZE on the projector or jRESIZE on the remote control Resize ModeImage Projection Continued VIDEOComputer About CopyrightsSwitching the Iris Setting Operating with the Remote ControlShifting the Projected Im- age Vertically Image Shift Freezing a Moving ImageThe following shows the items that can be set in the projector Menu Items“Picture” menu “C.M.S.”“Fine Sync” menu Menu Items Continued“Options1” menu “Options2” menuMenu Selections Adjustments Using the Menu Screenicon to adjust 1 Press dMENUTo adjust the projected image while watching it Using the Menu Screen Continued3 Press P or R to select the item to adjust Press O or Q to adjust the item selectedPicture Adjustment “Picture” menu 2Adjusting the Image1Selecting the Picture Mode 3Adjusting the Color Temperature Picture Adjustment “Picture” menu Continued4Adjusting the Colors 5 ProgressiveSetting 7Switching the Iris8Lamp Setting 6Reducing Image Noise2Special Modes Setting 1Adjusting the Computer Image3Auto Sync Auto Sync Adjustment 4Checking the Input Signal1Adjusting the Image Position Using the “Options” Menu2Adjusting the Overscan 3 Adjusting the Vertical Size of the Display Subtitle Setting4Setting On-screen Display Using the “Options” Menu Continued5Setting the Video System 6Signal Type SettingFunction 9Auto Power Off0Checking the Lamp Life Status 1 Reversing/Inverting Projected Images3Reducing the Power Consumption When the Power Is in Standby Mode 4Fan Mode Setting5Returning to the Default Settings 2Selectingthe Transmission the Speed RS-232C Speed RS-232CCleaning the projector MaintenanceCleaning the lens Cleaning the exhaust and intake ventsAbout the temperature warning indicator Maintenance IndicatorsAbout the lamp indicator Top ViewInfo If the temperature warning indicator illuminates, and the projector enters standby mode, follow the possible solutions above and then wait until the projector has cooled down completely before plug- ging in the power cord and turning the power back on. At least 10 minutesLamp Regarding the LampCaution Concerning the Lamp Replacing the Lamp2 Disconnect the power cord Removing and Installing the Lamp UnitInfo 3 Remove the lamp unit coverRegarding the Lamp Continued Resetting the Lamp Timer1 Connect the power cord 2 Reset the lamp timerConnecting Pin Assignments ProjectorComputer Connecting Pin Assignments Continued RS-232C Specifications and Command SettingsC1 C2 C4 P1 P2Computer Computer Compatibility ChartTroubleshooting 23-2723-27 23-27 ProblemSpecifications Units inches mm DimensionsStandard connector IndexTemperature warning indicator 11, 12U.S.A A-Key to better communicationsCanada Eastern Europe