Emerson 30-130 kVA Battery Power Pack, 25-Inch Cabinet, Outline Drawing, 1/22/03

BATTERY SERVICE ACCESS

CASTER CENTERS

12mm DIA. THREADED MOUNTING HOLE (4) TYP.

(SEE NOTES 12 & 13)

(SEE DETAIL A)

NOTES:

1.	ALL DIMENSIONS ARE IN INCHES.
2.	MIN CLEARANCE 36 INCHES IN FRONT, 12 INCHES
AT TOP FOR AIR EXHAUST.
3.	KEEP CABINET WITHIN 15° OF VERTICAL WHILE
HANDLING.

Figure 14

BIB

CONDUIT ENTRY 6.5 x 6.0

TOP ONLY

2 PLACES

MAX DOOR SWING 120°

2.72

12MM		CASTER
CENTERS
		CENTERS
	FRONT

12MM THREADED
MOUNTING HOLE	LEVELER

12MM CENTERS

DETAIL A

4.	EXTERIOR CABLE ENTRY AVAILABLE THROUGH
REMOVABLE TOP ACCESS PLATES. REMOVE, PUNCH
TO SUIT CONDUIT SIZE, AND REPLACE.
5.	CONTROL WIRING AND POWER WIRING MUST BE RUN
IN SEPARATE CONDUIT.
6.	ALUMINUM AND COPPER CLAD ALUMINUM CABLES ARE
NOT RECOMMENDED.
7.	ALL WIRING IS TO BE IN ACCORDANCE WITH
NATIONAL AND LOCAL ELECTRICAL CODES.
8.	RECOMMENDED OPERATING TEMPERATURE RANGE:

Outline Drawing,

BOARD

ACCESS

TOP VIEW

CENTER

GRAVITY

BOTTOM VIEW

CIRCUIT

BREAKER

CIRCUITMOTOR

BREAKER OPERATOR

OPTIONAL

DC BUS BARS

BATTERIES

NOTE:

(10)TRAY SHOWN.

(8)TRAY FOR FR200 BATTERY ASSY AND SMALLER

SUPPORT TRAY & SUPPORT BRACKET (SEE NOTE 15)

REAR OF UNIT SHOWN

WITHOUT SIDE PANEL

DC BUS BARS

CONTROL AND POWER WIRE SIDE ACCESS APPROX AREA 4.6 x 2.2

(BOTH SIDES)

CENTER

GRAVITY

68°F-77°F (20°C-25°C).

9. COLOR - IBM OFF WHITE.

10. UNIT BOTTOM IS STRUCTURALLY ADEQUATE FOR

FORKLIFT HANDLING.

11. APPROX WEIGHT OF CABINET IS 1500 TO 3000 LBS.

12. THREADED MOUNTING HOLES USED FOR SEISMIC

ANCHORING OR FLOORSTAND. NOTE, IF FLOORSTAND

IS USED THE WEIGHT OF THE UNIT MUST BE

SUPPORTED UNDER ALL CASTERS.

13. EACH MOUNTING LOCATION IS SUPPORTED

BY (2) 10 GA. (.135") GALVANIZED STEEL. THE THREADED 12MM INSERT IS APPROX. 3/4" DEEP.

MOUNTING BOLTS MUST BE THREADED INTO UNIT MOUNTING HOLES FROM UNDERNEATH UNIT BASE.

14.REFER TO DETAIL A FOR DIMENSION TO FRAME WITH SIDE PANEL REMOVED. SIDE PANELS ARE REMOVED BETWEEN ADJACENT UNITS WHICH ARE BOLTED TOGETHER.

15."BEFORE SLIDING OUT BATTERIES ON BATTERY TRAY" POSITION SUPPORT TRAY AND ATTACH TO CABINET. THEN SECURE (2) SUPPORT BRACKETS TO THE SUPPORT TRAY AND TO THE CABINET. REFER TO THE APPROPRIATE USERS MANUAL FOR FURTHER DESCRIPTION & DETAILS.

Battery Power Pack, 25-Inch Cabinet

Installation Drawings 33

FRONT VIEW	FRONT VIEW
	WITH DOOR AND		SIDE VIEW
WITH DOOR		WITH COVER REMOVED
	BARRIER REMOVED			DETAIL FOR DC BUS BARS
DRAWN BY
V CARMONA	OUTLINE DRAWING
CHK BY		DWG. NO.
	25" BATTERY CABINET
			UBC11001
	NPOWER
REF. DWG.		REV. NO.	DATE	1050 DEARBORN DRIVE,
		3	1/22/03	COLUMBUS, OHIO 43229
		FILE NAME: Batts\UBC11001-03