34 Installation Drawings
AIR EXHAUST CUTOUT
6 PLACES
CASTER CENTERS
12MM
CENTERS
CONDUIT ENTRY
5.5 X 11.0FRONT TOP AND BOTTOM
DC BUS BARS
12mm DIA. THREADED MOUNTING HOLE (6) TYP. (SEE NOTES 12 & 13)
(SEE DETAIL A)
CASTER
CENTERS
2.72
NOTES:
1.ALL DIMENSIONS ARE IN INCHES.
2.MIN CLEARANCE 36 INCHES IN FRONT, 12 INCHES AT TOP FOR AIR EXHAUST.
3.KEEP CABINET WITHIN 15° OF VERTICAL WHILE HANDLING.
4.EXTERIOR CABLE ENTRY AVAILABLE THROUGH REMOVABLE TOP AND BOTTOM ACCESS PLATES. REMOVE, PUNCH TO SUIT CONDUIT SIZE, AND REPLACE.
5.CONTROL WIRING AND POWER WIRING MUST BE RUN IN SEPARATE CONDUIT.
6.ALUMINUM AND COPPER CLAD ALUMINUM CABLES ARE NOT RECOMMENDED.
7.ALL WIRING IS TO BE IN ACCORDANCE WITH
Figure 15 Outline Drawing,
MAX DOOR SWING 120°- LIFT OFF DOORS | 12MM CENTERS |
|
TOP VIEW | BOTTOM VIEW |
12MM THREADED |
|
MOUNTING HOLE | LEVELER |
NATIONAL AND LOCAL ELECTRICAL CODES.
8. | RECOMMENDED OPERATING TEMPERATURE RANGE: |
9. | COLOR - IBM OFF WHITE. |
10. UNIT BOTTOM IS STRUCTURALLY ADEQUATE FOR | |
FORKLIFT HANDLING. | |
Battery Power
CIRCUIT
DETAIL A
REAR OF UNIT SHOWN
11. APPROX WEIGHT OF CABINET IS 3500 TO 5100 LBS. |
BREAKER
BATTERIES
WITHOUT SIDE PANEL
MOTOR
OPERATOR
OPTIONAL
12. THREADED MOUNTING HOLES USED FOR SEISMIC |
ANCHORING OR FLOORSTAND. NOTE, IF FLOORSTAND |
IS USED THE WEIGHT OF THE UNIT MUST BE |
SUPPORTED UNDER ALL CASTERS. |
13. EACH MOUNTING LOCATION IS SUPPORTED |
BY (2) 10 GA. (.135") GALVANIZED STEEL. THE
THREADED 12MM INSERT IS APPROX. 3/4" DEEP.
CIRCUIT | CONTROL AND | |
BREAKER | POWER WIRE | |
| SIDE ACCESS | |
BUS BARS | APPROX AREA | |
4.56 x 2.25 | ||
| ||
| (BOTH SIDES) | |
CENTER | CENTER | |
GRAVITY | GRAVITY | |
SUPPORT TRAY & |
| |
SUPPORT BRACKET |
| |
(SEE NOTE 15) |
|
MOUNTING BOLTS MUST BE THREADED INTO UNIT
MOUNTING HOLES FROM UNDERNEATH UNIT BASE.
14.REFER TO DETAIL A FOR DIMENSION TO FRAME WITH SIDE PANEL REMOVED. SIDE PANELS ARE REMOVED BETWEEN ADJACENT UNITS WHICH ARE BOLTED TOGETHER.
15."BEFORE SLIDING OUT BATTERIES ON BATTERY TRAY" POSITION SUPPORT TRAY AND ATTACH TO CABINET. THEN SECURE (2) SUPPORT BRACKETS TO THE SUPPORT TRAY AND TO THE CABINET. REFER TO THE APPROPRIATE LIEBERT USERS MANUAL FOR FURTHER DESCRIPTION & DETAILS.
| FRONT VIEW |
| SIDE VIEW |
| |
FRONT VIEW | WITH DOORS REMOVED |
| DETAIL FOR DC BUS BARS | ||
WITH COVER REMOVED | |||||
|
|
| |||
DRAWN BY |
|
|
|
| |
V CARMONA | OUTLINE DRAWING |
|
|
| |
CHK BY | DWG. NO. |
|
| ||
49" BATTERY CABINET |
|
| |||
|
| UBC11003 |
| ||
| NPOWER |
|
| ||
REF. DWG. | REV. NO. | DATE | 1050 DEARBORN DRIVE, | ||
|
| 3 | 1/22/03 | COLUMBUS, OHIO 43229 | |
|
| FILE NAME: |
| ||
Pack,
