Enviro 50-029 Operating Instructions, For Your Safety Read Completely Before Operating

Operating Instructions

FOR YOUR SAFETY READ COMPLETELY BEFORE OPERATING.

LIGHTING INSTRUCTIONS:

CAUTION:Hot while operating. Do not touch. Keep children, clothing, furniture, gasoline or other flammable vapors away.

FOR YOUR SAFETY: Do not operate this fireplace with the glass removed, cracked or broken. Replacement of this glass should be done by a licensed or qualified person! This appliance needs fresh air for safe operation and must be installed with provisions for combustion and ventilation air.

See installation and operating instructions manual. Keep burner and control compartment clean . WARNING: Improper installation, adjustment, alteration, service or maintenance can cause property damage, personal injury, or loss of life. Refer to owners manual. Installation and service must be performed by qualified installer, service agency or the gas supplier.

FOR YOUR SAFETY READ BEFORE OPERATING

WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, AFIREOR EXPLOSION MAY RESULT CAUSING

PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.

A)This appliance is e quippe d with a pilot, which mustbe litbyIf you cannot re ach your gas supp lier, call the fire departm ent. hand b y following these instructions e xactly.

B)BEFORE LIGHTING smell all around the appliance area for gas and n ext to the floor because some gas is heavi er

than air and will se ttle on the floor.

WHAT TO DO IF YOU SMELL GAS:

Do not try to light any a pplian ce. Do not touch a ny electrical switch: do not use any phone in you r building.

Immediately call your gas sup plier from a neighbors p hone. Follo w the gas supplie rs instr uctions.

C)Use only your ha nd to p ush in or tu rn the gas co ntrol knob,

	Neve r use tools. If the knob will not push in or turn by
	hand , do n ot try to rep air it.
	Call a qual ified service techn ician. Force or attempte d
D)	repair may result in a fire or explosion.
	Do n ot use thisa pplian ce if any part has b een u nder water.
	Immediately call a qualified service technician to inspe ct
	the a ppliance an d to replace any pa rt of the con trol system
	and any ga s con trol which ha s been unde r water.

LIGHTING INSTRUCTIONS

1.STOP! Read th e safe ty information above on th is labe l.

2.Turn off all electrical power to this applian ce.

3. Turn off the gas contr ol knob clockwise	to the off
position.

4.Open door. Wa it five (5) minutes to clear outany gas.

	Cl ose do or. If you sme ll gas, includ ing ne ar the floor ,
	STOP! Follow “ B” in the	above safety information.
5.	If you do not smell gas go to the ne xt ste p
	Fin d pilo t-locate d to th e righ t behin d the side log. Turn
	the gas control
	kn ob cou nter-clockwise	to “PILOT”.
	Push the gas co ntrol in

ful ly and hold, Keep knob

depressed for a bout 30 seco nds after pilot is lit. Release kno b. If p ilot goes out, rep eatsteps 4 through 5.

WARNING: this gas valve ha s a lockout device, which will n ot allow the pilot burner to be relit until the ther mocouple h as cooled. If the knob does not po p up when released, stop and imme diately call yo ur service technician or gas supplier.

If the pilot does not stay lit after several tries, turn the gas control knob to “OFF” and call your service technician or g as supplier.

6.Turn the gas control knob counter clockwise to the “ON” position. Flip the burner switch to

“ON” THEN TURN THE “HI/LOW” knob to the desired setting. 7. Turn on the ele ctrical power to the unit.

TO TURN OFF GAS TO APPLIANCE

1.	Fli p burn er switch to “OFF”	to th e “OF F”	3 . Turn off all electrical po wer to the ap pliance if service i sto
2.	Turn the gasco ntrol knob clockwise		be performe d.
	po sition		ACLIE -1

Figure 3. Lighting instruction label.

PILOT LIGHT:

1.Turn off the gas to the fireplace. If not recently done, remove the glass and let the unit air out for at least five (5) minutes to clear out any gas. Turn on gas to the heater. Leak test all joints with soapy water. NEVER USE AN OPEN FLAME FOR LEAK TESTING.

2.Start the pilot by pressing the gas control knob and turning it to PILOT. While holding the gas control knob in, press the piezo ignitor several times until the pilot light starts. Hold the gas control knob in for thirty (30) seconds. Check that the pilot has fully engulfed the thermocouple assembly (see Figure 4).

3.Start the main burner by turning the gas control knob to ON and then turn the rocker switch to ON. Check that all burner ports have flame.

4.Leak test all gas joints again.

���������� ������������

Figure 4. Pilot flame.

6