Initial Installation

4.After a minimum of 10 minutes operation, test the chimney draft with a smoke match at the top row of the pattern to confirm that there is adequate draft or ‘pull’ at the openings around the body of the Drafthood Adaptor, as shown in Figure 26.

AUTOMATIC SAFETY SHUT DOWN:

If the spill switch is activated and shuts off the main burner the following procedure should be followed.

•Is the pilot flame still on? If not, the reason for the fireplace shut down is not the spill switch.

•Turn off the pilot flame and turn off all controls. Let fireplace to cool down. Refer to Owner’s Manual.

•Check for blockages or restrictions in the flue and venting components.

•Restart the fireplace and check for vent draft as described earlier.

•Operate the fireplace in a normal manner.

•If the main burner shuts down again after a period of operation, turn off the fireplace and contact your service technician.

SPILL SWITCH REPLACEMENT:

Use the following instructions to replace the Safety Spill Switch.

1.Turn the unit off and allow it to cool.

2.Disconnect the spill switch wires from the valve and on/off/remote rocker switch wire (see Figure 23).

3.Remove the four mounting screws holding the spill switch bracket and remove the bracket (see Figure 27).

4.Remove and replace the spill switch with a 50-885 Spill Switch Assembly using a T-20 torx type driver.

5.Follow the reverse of the previous steps.

OPTIONAL FINISHING:

Figure 27: Spill switch installation.

In installations where the flue connector is running from the drafthood into a non-combustible chimney the following optional finishing technique can be used.

CAUTION: Installations where the flue connector or venting connects to, or passes through, combustible walls or ceilings, the inner vent components must be ‘B-vent’. It is not allowable in these applications to use single wall inner vent components.

For decorative purposes a 6” (15 cm) single wall black stove pipe may be installed over the 4” (10 cm) single wall or ‘B-Vent’.

Note: The use of these components is for aesthetic purposes only and does not effect the fact that the fireplace, when fitted with the Drafthood Adaptor, is a Natural Vent appliance and therefore draws air in through the Drafthood Adaptor intake ports.

21

Page 20 Page 22
Page 21
Image 21
Enviro 50-029 owner manual Automatic Safety Shut Down, Spill Switch Replacement, Optional Finishing
Page 20 Page 22

50-029 specifications

Enviro 50-029 is an innovative environmental monitoring device designed to provide comprehensive data collection and analysis for various ecological parameters. With its cutting-edge features, the device has garnered attention in industries such as agriculture, environmental science, and urban planning.

One of the cornerstone features of the Enviro 50-029 is its multi-sensor capability. This device is equipped with a suite of sensors that can measure a wide range of environmental variables. These include temperature, humidity, air quality, soil moisture, and light intensity. The integration of multiple sensors allows users to gather detailed insights into the ecosystem, enabling better decision-making and resource management.

The Enviro 50-029 also utilizes advanced wireless communication technologies, such as LoRaWAN and Zigbee. This allows for real-time data transmission without the need for extensive wiring or infrastructure. The device can connect to a central hub or cloud-based platform, facilitating remote monitoring and accessibility of data from anywhere in the world. This feature is particularly valuable for researchers and environmental agencies monitoring remote or hard-to-reach areas.

Power efficiency is another significant characteristic of the Enviro 50-029. Utilizing low-power design protocols, the device can operate for extended periods on minimal battery power. This sustainability aspect is crucial, particularly for long-term environmental monitoring projects where replacing batteries frequently can be logistically challenging.

Moreover, the Enviro 50-029 is built to withstand various environmental conditions. Its robust, weather-resistant casing ensures durability in extreme temperatures and harsh weather environments. This makes it suitable for outdoor deployments, whether in agricultural fields, forests, or urban areas, without compromising performance.

The device also supports customizable settings, enabling users to define specific thresholds and alerts for different environmental parameters. This feature allows for proactive monitoring and notifications on critical changes, providing essential data needed to respond to environmental concerns swiftly.

Overall, the Enviro 50-029 stands out as a versatile and reliable tool for environmental monitoring. Its multi-sensor capabilities, advanced communication technologies, power efficiency, and robust design make it an excellent choice for research, conservation efforts, and smart farming applications. By integrating such a sophisticated device into their operations, users can gain actionable insights and contribute to a more sustainable future.
Top Page Image Contents