![from this plug.](/images/new-backgrounds/55767/5576747x1.webp)
Initial Installation
ELECTRICAL REQUIREMENTS:
The ENVIRO ASCOT will operate without electrical power. This model has a millivolt gas control, which uses the pilot flame to generate enough electricity to operate the main burners. The appliance when equipped with an optional blower must be electrically connected and grounded in accordance with local codes or in the absence of local codes, with the current CSA C22.1 CANADIAN ELECTRICAL CODE Part
1, SAFETY STANDARDS FOR ELECTRICAL INSTALLATIONS, OR THE NATIONAL ELECTRICAL CODE ANSI / NFPA 70 in the U.S.
WARNING: Electrical grounding instructions. This appliance is equipped with a
from this plug. |
|
|
|
|
|
| Wire Size | Max. Length | |||
CAUTION: Label all wires prior to disconnection when servicing | |||||||||||
14 gauge | 100 ft | (30.48 m) | |||||||||
controls. | Wiring | errors | can | cause | improper | and | dangerous | ||||
16 gauge | 60 ft | (18.29 m) | |||||||||
operation. Verify proper operation after servicing. |
|
| |||||||||
|
| 18 gauge | 40 ft | (12.00 m) | |||||||
|
|
|
|
|
|
|
| ||||
|
|
| ON/OFF/Thermostat |
|
| 20 gauge | 25 ft | (7.62 m) | |||
|
|
|
|
| 22 gauge | 18 ft | (5.49 m) | ||||
|
|
|
|
|
|
|
| ||||
Purple |
| Blue |
|
|
|
|
|
| |||
| Thermopile |
|
| ����� |
| ��� |
| ||||
|
|
|
|
|
|
|
| ||||
|
|
|
| Gas Control |
|
|
|
|
| ||
| Grey |
|
| Valve |
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
| ����� | ||
|
|
|
|
|
|
| ����� |
|
| ||
|
|
|
|
|
|
|
|
|
| ||
70 ° F |
|
|
|
|
|
|
|
| ����� |
| |
|
|
|
| Pilo |
|
|
|
|
|
| |
DOWN | Optional | Adjustment |
|
| ��� |
|
|
| |||
COOL / HEAT |
|
|
|
|
|
|
|
| |||
UP |
|
|
| Screw |
|
|
|
|
|
| |
PROGRAM | Thermostat |
|
|
| ����������� |
| ����� ������ |
| |||
|
|
|
|
| ������ |
| ��� | ||||
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
| ���������� |
Figure 29. Wiring Diagram For Gas Valve. | Figure 30. Wiring Diagram For Fan Control. |
INSTALLATION OF OPTIONAL BLOWER:
���� � ���� �� |
��� ����������� |
������ |
������ ������ |
��� ���������� |
��� ����������� |
������ ������ |
�������� ��� |
Figure 31: Optional Fan Kit Installation.
Remove the
Place the fan assembly behind the unit and secure with the two screws provided (as shown in Figure 31).
Remove the fan controller, mounting box and install fan controller. Neatly dress the wires from the fan assembly to the fan controller.
Install the fan temperature sensor with the two (2) screws provided.
Plug the fan assembly into the wall outlet and turn the unit on to ensure fan operation.
24