Initial Installation

QUALIFIED INSTALLERS ONLY

HORIZONTAL INSTALLATION:

STEP 1. Set the appliance in the desired location. Check to determine if wall studs or roof rafters are in the way when the venting system is attached. If this is the case, you may want to adjust the location of the appliance.

STEP 2. Direct vent pipe and fittings are designed with special twist-lock connections. Assemble the desired combination of black pipe and elbows to the appliance adapter with pipe seams oriented towards the wall or floor, as much out of view as possible.

 

Place a bead of Mil-Pac on the

10"

 

(254mm)

 

outer edge of the inner exhaust

 

 

pipe (non-flared end). Place a bead

 

Female

of high temperature silicone on the

10"

male edge of the outer pipe. Push the

(254mm)

Locking

 

Lugs

pipe sections completely together,

 

Sealant

then twist-lock one section clockwise

 

approximately 1⁄4 turn, until the two

 

Male

 

sections are fully locked. The female

 

Locking

 

Lugs

locking lugs will not be visible from

 

 

the outside, on black pipe. They may

 

 

be located by examining the inside of

 

Figure 12: Twist-Lock Connection

the female ends as shown in Figure

Figure 13: Wall Framing Hole for

12.

 

Horizontal Installation.

 

 

Notes:

(1)Twist-lock procedure: four (4) indentations, located on the female end of the pipes and fittings, are designed to slide straight onto the male ends of adjacent pipes and fittings, by orienting the four pipe indentations so they match and slide into the four entry slots on the male end.

(2)Horizontal runs of vent pipe must be supported every three feet. Wall straps are available for this purpose, also when running horizontal pipe minimum clearances to combustibles must be maintained; 2 inches (5.1 cm) at top, 11⁄2 inches (3.8 cm) at sides, 11⁄2 inches (3.8 cm) at bottom.

11/4"

 

(3.2cm)

 

Fold strap

Woodscrews

 

here

 

Sheet metal

 

screws

 

 

Wall Thimble

 

Strap

Figure 14: Installing Decorative Wall Thimble.

14

Page 14
Image 14
Enviro 50-029 owner manual High temperature silicone on

50-029 specifications

Enviro 50-029 is an innovative environmental monitoring device designed to provide comprehensive data collection and analysis for various ecological parameters. With its cutting-edge features, the device has garnered attention in industries such as agriculture, environmental science, and urban planning.

One of the cornerstone features of the Enviro 50-029 is its multi-sensor capability. This device is equipped with a suite of sensors that can measure a wide range of environmental variables. These include temperature, humidity, air quality, soil moisture, and light intensity. The integration of multiple sensors allows users to gather detailed insights into the ecosystem, enabling better decision-making and resource management.

The Enviro 50-029 also utilizes advanced wireless communication technologies, such as LoRaWAN and Zigbee. This allows for real-time data transmission without the need for extensive wiring or infrastructure. The device can connect to a central hub or cloud-based platform, facilitating remote monitoring and accessibility of data from anywhere in the world. This feature is particularly valuable for researchers and environmental agencies monitoring remote or hard-to-reach areas.

Power efficiency is another significant characteristic of the Enviro 50-029. Utilizing low-power design protocols, the device can operate for extended periods on minimal battery power. This sustainability aspect is crucial, particularly for long-term environmental monitoring projects where replacing batteries frequently can be logistically challenging.

Moreover, the Enviro 50-029 is built to withstand various environmental conditions. Its robust, weather-resistant casing ensures durability in extreme temperatures and harsh weather environments. This makes it suitable for outdoor deployments, whether in agricultural fields, forests, or urban areas, without compromising performance.

The device also supports customizable settings, enabling users to define specific thresholds and alerts for different environmental parameters. This feature allows for proactive monitoring and notifications on critical changes, providing essential data needed to respond to environmental concerns swiftly.

Overall, the Enviro 50-029 stands out as a versatile and reliable tool for environmental monitoring. Its multi-sensor capabilities, advanced communication technologies, power efficiency, and robust design make it an excellent choice for research, conservation efforts, and smart farming applications. By integrating such a sophisticated device into their operations, users can gain actionable insights and contribute to a more sustainable future.