Manuals / Enviro / Household Appliance / Stove

Enviro C-11150 technical manual Installation, Refer to Figures 17 and

Models: C-11150

1 34

Page 15

	Installation
HEARTH MOUNT INSTALLATION:
	��
	��
Flue	��	Refer to Figures 17 and 18.
Flue	��
Connector	��
Connector	��	1.	Install the hearth pad.
	��

		2.	Lock fireplace damper in the open position.
		3.	Install a positive flue connector at the
			fireplace dampers or seal the chimney at
			the top.
��		4.	Connect a tee to the exhaust pipe.
	��	5.	Install flexible stainless steel liner or listed
	��
			pellet vent to the top of the chimney.
	��
	��
��	��

Figure 17: Freestanding hearth mount installation.

Rain cap

Storm collar

Seal plate (cover plate)

Existing masonry flue

Vent pipe (single wall stainless flex pipe or solid PL vent)

Flexible vent connector (use this 5 foot [152cm] section of pipe to vent past fireplace damper or small shelf)

Fireplace damper location

Clean out tee

Existing fireplace

Figure 18: Freestanding hearth mount installation overview.

Page 15

Image 15

Enviro C-11150 technical manual Installation, Refer to Figures 17 and

Contents

PELLET STOVE 50-1221Mini TECHNICAL MANUALTable of Contents Introduction Caution Do not connect to any air distribution duct or systemTHE USE OF CORDWOOD IS PROHIBITED BY LAW Introduction SOOT Operation of the stove with insufficient combustion air will result in the formation of soot which will collect on the glass, the heat exchanger, the exhaust vent system, and may stain the outside of the house. This is a dangerous situation and is inefficient. Frequently check your stove and adjust the slider/ damper as needed to ensure proper combustion. See “SLIDER/DAMPER SETTING”Introduction SAVE THIS INSTRUCTION MANUAL FOR FUTURE REFERENCEInstallation 1. Remove the cab sides and ash pan cover InstallationInstall vent at clearances specified by the vent manufacturer InstallationNOTE Venting terminals shall not be recessed into walls or siding InstallationInstallation EXHAUSTFRESH AIR INTAKE Secure the heater to the floor using the two holes in the pedestal Installationstove InstallationFigure 11 Straight through wall Installation Figure 12 Venting to use with straight through wall InstallationFigure 13 is the recommended installation set up InstallationPlace a non-combustible hearth pad where InstallationRefer to Figures 17 and Installation1 - Blower cover plate 1 - Hardware bag InstallationInstallation Figure 22 Through Wall Installation with Exterior Blower KitWall Strap To supply power to the exhaust blower Sheathing InstallationRoof Sheathing Rain Cap Roof Flashing Roof Rafters Ceiling Joists Vent Pipecabinet side and locate the slider damper plate. Install the InstallationSPECIAL NOTES InstallationTools Required InstallationThis kit must be installed before the unit is started Installing the PanelsInstalling Hopper Lid InstallationWHAT TO DO IF Troubleshooting2. The stove will not operate when hot DO NOT4. Light # 2 on Heat output bar flashing Troubleshooting6. The 200 F 93 C high limit temperature sensor has tripped 3. The exhaust motor will not function normally8. Ignitor- the pellets will not light Troubleshooting9. Control settings Heat Level has no effect on the fire 7. The convection blower will not function normallyWiring Diagram Part Number Parts ListReference DescriptionPart Number Parts ListReference DescriptionParts Diagram - Components Mini - ComponentsNovember SDiagramPartsteel Mini - Steel ComponentsNovember Limited Two 2 Year Warranty WarrantyLimited Lifetime Warranty Limited Three 3 Year WarrantyExclusions and Limitations Warranty17. Damage to plated surfaces caused by fingerprints, scratches, melted items, or other external scores and residues left on the plated surfaces from the use of abrasive cleaners or polishes is not covered in this warranty Warranty6782 OLDFIELD RD. SAANICHTON, BC, CANADA V8M 2A3 Installation Data Sheet

Refer to Figures 17 and 18.