Manuals / Enviro / Household Appliance / Stove

Enviro C-11150 Installation, Secure the heater to the floor using the two holes in the pedestal

Models: C-11150

1 34

Download 34 pages 57.64 Kb

Page 11

●Secure the heater to the floor using the two holes in the pedestal.

Installation

MOBILE HOME INSTALLATION:

●Secure the heater to the floor using the two holes in the pedestal.

●Ensure the unit is electrically grounded to the chassis of your home (permanently).

●Do not install in a room people sleep in.

●Outside fresh air is mandatory. Secure outside air connections directly to fresh air intake pipe and secure with three (3) screws evenly spaced.

CAUTION: THE STRUCTURAL INTEGRITY OF THE MANUFACTURED HOME FLOOR, WALL AND CEILING/ROOF MUST BE MAINTAINED.

ENVIRO Mini
Optional
Hearth Pad
Flooring
Steel Frame
1/4” Lag Bolts	Ground Wire Directly
Securely Fastened	to Metal Chassis

Figure 9: Mobile home installation.

CORNER THROUGH WALL INSTALLATION:

3" (75mm)

3" (75mm)

Wall thimble

manufactured by pellet vent manufacturer.

Figure 10: Corner Installation.

11

Image 11

Enviro C-11150 technical manual Installation, Secure the heater to the floor using the two holes in the pedestal

Contents

PELLET STOVE 50-1221Mini TECHNICAL MANUALTable of Contents THE USE OF CORDWOOD IS PROHIBITED BY LAW IntroductionCaution Do not connect to any air distribution duct or system Introduction SOOT Operation of the stove with insufficient combustion air will result in the formation of soot which will collect on the glass, the heat exchanger, the exhaust vent system, and may stain the outside of the house. This is a dangerous situation and is inefficient. Frequently check your stove and adjust the slider/ damper as needed to ensure proper combustion. See “SLIDER/DAMPER SETTING”Introduction SAVE THIS INSTRUCTION MANUAL FOR FUTURE REFERENCEInstallation 1. Remove the cab sides and ash pan cover InstallationInstall vent at clearances specified by the vent manufacturer InstallationNOTE Venting terminals shall not be recessed into walls or siding InstallationFRESH AIR INTAKE InstallationEXHAUST Secure the heater to the floor using the two holes in the pedestal Installationstove InstallationFigure 11 Straight through wall Installation Figure 12 Venting to use with straight through wall InstallationFigure 13 is the recommended installation set up InstallationPlace a non-combustible hearth pad where InstallationRefer to Figures 17 and Installation1 - Blower cover plate 1 - Hardware bag InstallationWall Strap To supply power to the exhaust blower InstallationFigure 22 Through Wall Installation with Exterior Blower Kit Sheathing InstallationRoof Sheathing Rain Cap Roof Flashing Roof Rafters Ceiling Joists Vent Pipecabinet side and locate the slider damper plate. Install the InstallationSPECIAL NOTES InstallationTools Required InstallationThis kit must be installed before the unit is started Installing the PanelsInstalling Hopper Lid InstallationWHAT TO DO IF Troubleshooting2. The stove will not operate when hot DO NOT4. Light # 2 on Heat output bar flashing Troubleshooting6. The 200 F 93 C high limit temperature sensor has tripped 3. The exhaust motor will not function normally8. Ignitor- the pellets will not light Troubleshooting9. Control settings Heat Level has no effect on the fire 7. The convection blower will not function normallyWiring Diagram Part Number Parts ListReference DescriptionPart Number Parts ListReference DescriptionNovember Parts Diagram - ComponentsMini - Components November SDiagramPartsteelMini - Steel Components Limited Two 2 Year Warranty WarrantyLimited Lifetime Warranty Limited Three 3 Year WarrantyExclusions and Limitations Warranty17. Damage to plated surfaces caused by fingerprints, scratches, melted items, or other external scores and residues left on the plated surfaces from the use of abrasive cleaners or polishes is not covered in this warranty Warranty6782 OLDFIELD RD. SAANICHTON, BC, CANADA V8M 2A3 Installation Data Sheet