Manuals
/
Enviro
/
Household Appliance
/
Stove
Enviro
C-11150 technical manual Parts Diagram - Components, Mini - Components, November
Models:
C-11150
1
29
34
34
Download
34 pages
57.64 Kb
26
27
28
29
30
31
32
33
<
>
Troubleshooting
Install
Parts list
Wiring Diagram
Warranty
SOOT Operation of the stove with insufficient combustion air will result in the formation of soot which will collect on the glass, the heat exchanger, the exhaust vent system, and may stain the outside of the house. This is a dangerous situation and is inefficient. Frequently check your stove and adjust the slider/ damper as needed to ensure proper combustion. See “SLIDER/DAMPER SETTING”
Control settings Heat Level has no effect on the fire
The 200 F 93 C high limit temperature sensor has tripped
Wall Strap To supply power to the exhaust blower
Secure the heater to the floor using the two holes in the pedestal
Page 29
Image 29
Parts Diagram - Components
��
�
�
��
��
��
��
��
�
��
�
��
��
�
�
�
�
Mini - Components
��
November 2006
29
Page 28
Page 30
Page 29
Image 29
Page 28
Page 30
Contents
Mini
50-1221
TECHNICAL MANUAL
PELLET STOVE
Table of Contents
THE USE OF CORDWOOD IS PROHIBITED BY LAW
Introduction
Caution Do not connect to any air distribution duct or system
Introduction
SOOT Operation of the stove with insufficient combustion air will result in the formation of soot which will collect on the glass, the heat exchanger, the exhaust vent system, and may stain the outside of the house. This is a dangerous situation and is inefficient. Frequently check your stove and adjust the slider/ damper as needed to ensure proper combustion. See “SLIDER/DAMPER SETTING”
Introduction
SAVE THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE
Installation
1. Remove the cab sides and ash pan cover
Installation
Install vent at clearances specified by the vent manufacturer
Installation
NOTE Venting terminals shall not be recessed into walls or siding
Installation
FRESH AIR INTAKE
Installation
EXHAUST
Secure the heater to the floor using the two holes in the pedestal
Installation
Figure 11 Straight through wall Installation
Installation
Figure 12 Venting to use with straight through wall Installation
stove
Figure 13 is the recommended installation set up
Installation
Place a non-combustible hearth pad where
Installation
Refer to Figures 17 and
Installation
1 - Blower cover plate 1 - Hardware bag
Installation
Wall Strap To supply power to the exhaust blower
Installation
Figure 22 Through Wall Installation with Exterior Blower Kit
Roof Sheathing Rain Cap Roof Flashing Roof Rafters Ceiling Joists
Installation
Vent Pipe
Sheathing
cabinet side and locate the slider damper plate. Install the
Installation
SPECIAL NOTES
Installation
This kit must be installed before the unit is started
Installation
Installing the Panels
Tools Required
Installing Hopper Lid
Installation
2. The stove will not operate when hot
Troubleshooting
DO NOT
WHAT TO DO IF
6. The 200 F 93 C high limit temperature sensor has tripped
Troubleshooting
3. The exhaust motor will not function normally
4. Light # 2 on Heat output bar flashing
9. Control settings Heat Level has no effect on the fire
Troubleshooting
7. The convection blower will not function normally
8. Ignitor- the pellets will not light
Wiring Diagram
Reference
Parts List
Description
Part Number
Reference
Parts List
Description
Part Number
November
Parts Diagram - Components
Mini - Components
November
SDiagramPartsteel
Mini - Steel Components
Limited Lifetime Warranty
Warranty
Limited Three 3 Year Warranty
Limited Two 2 Year Warranty
Exclusions and Limitations
Warranty
17. Damage to plated surfaces caused by fingerprints, scratches, melted items, or other external scores and residues left on the plated surfaces from the use of abrasive cleaners or polishes is not covered in this warranty
Warranty
6782 OLDFIELD RD. SAANICHTON, BC, CANADA V8M 2A3
Installation Data Sheet