Manuals / Enviro / Household Appliance / Stove

Enviro C-11150 Installation, Roof Sheathing Rain Cap Roof Flashing Roof Rafters Ceiling Joists

Models: C-11150

1 34

Download 34 pages 57.64 Kb

Page 18

Roof Sheathing

Installation

TYPICAL THROUGH WALL WITH EXTERIOR BLOWER KIT INSTALLATION - VERTICAL TERMINATION:

Follow the previous pages for through wall installations. Ensure that vent pipe is properly secured to wall using wall straps. Maintain clearances to combustibles on vent pipe as well as unit.

Roof Sheathing

Rain Cap

Roof Flashing

Roof Rafters

Ceiling Joists

Vent Pipe

Exterior Wall

Sheathing

Outside Vent

Termination

Figure 24: Through Wall Installation with Exterior Blower Kit; Vertical Termination.

18

Image 18

Enviro C-11150 Installation, Roof Sheathing Rain Cap Roof Flashing Roof Rafters Ceiling Joists, Vent Pipe, Termination

Contents

TECHNICAL MANUAL 50-1221Mini PELLET STOVETable of Contents Introduction Caution Do not connect to any air distribution duct or systemTHE USE OF CORDWOOD IS PROHIBITED BY LAW SOOT Operation of the stove with insufficient combustion air will result in the formation of soot which will collect on the glass, the heat exchanger, the exhaust vent system, and may stain the outside of the house. This is a dangerous situation and is inefficient. Frequently check your stove and adjust the slider/ damper as needed to ensure proper combustion. See “SLIDER/DAMPER SETTING” IntroductionSAVE THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE IntroductionInstallation Installation 1. Remove the cab sides and ash pan coverInstallation Install vent at clearances specified by the vent manufacturerInstallation NOTE Venting terminals shall not be recessed into walls or sidingInstallation EXHAUSTFRESH AIR INTAKE Installation Secure the heater to the floor using the two holes in the pedestalFigure 12 Venting to use with straight through wall Installation InstallationFigure 11 Straight through wall Installation stoveInstallation Figure 13 is the recommended installation set upInstallation Place a non-combustible hearth pad whereInstallation Refer to Figures 17 andInstallation 1 - Blower cover plate 1 - Hardware bagInstallation Figure 22 Through Wall Installation with Exterior Blower KitWall Strap To supply power to the exhaust blower Vent Pipe InstallationRoof Sheathing Rain Cap Roof Flashing Roof Rafters Ceiling Joists SheathingInstallation cabinet side and locate the slider damper plate. Install theInstallation SPECIAL NOTESInstalling the Panels InstallationThis kit must be installed before the unit is started Tools RequiredInstallation Installing Hopper LidDO NOT Troubleshooting2. The stove will not operate when hot WHAT TO DO IF3. The exhaust motor will not function normally Troubleshooting6. The 200 F 93 C high limit temperature sensor has tripped 4. Light # 2 on Heat output bar flashing7. The convection blower will not function normally Troubleshooting9. Control settings Heat Level has no effect on the fire 8. Ignitor- the pellets will not lightWiring Diagram Description Parts ListReference Part NumberDescription Parts ListReference Part NumberParts Diagram - Components Mini - ComponentsNovember SDiagramPartsteel Mini - Steel ComponentsNovember Limited Three 3 Year Warranty WarrantyLimited Lifetime Warranty Limited Two 2 Year WarrantyWarranty Exclusions and LimitationsWarranty 17. Damage to plated surfaces caused by fingerprints, scratches, melted items, or other external scores and residues left on the plated surfaces from the use of abrasive cleaners or polishes is not covered in this warrantyInstallation Data Sheet 6782 OLDFIELD RD. SAANICHTON, BC, CANADA V8M 2A3