Epson 670 6.1 Preventive Maintenance

Chapter 6 Maintenance

Rev. A 6-1

6.1 Preventive Maintenance

Preventive Maintenance is important to keep the printer in the best condition and to prevent troubles in

advance. Use the denatured alcohol to clean the exterior case and use the vacuum cleaner if necessary,

to remove dust and paper debris in the printer inside.

CAUTION

;

Do not use thinner, trichloroethylene, or ketone-based solvents on the plastic components of the

printer.

;

Never use the oil and the grease other than those specified in this manual, and using different type

of lubrication can damage the printer and the components.

;

Disconnect the printer from the AC socket before performing maintenance.

The influence that grease and oil give is great and especially in low temperature. Therefore, EPSON has

been tested and analyzed various grease and oil extensively and chooses the best one for that printer.

Type Name Quantity Availability Part No.

Grease G-26 40g EPSON B702600001

Oil O-8 40cc EPSON 1019753

Ref. No. Lubrication Points Lubricant

1 Contact area of the frame, base, shaft and release G-26(3-5mg)

2 Contact area around the gear 20 of the release lever G-26(3-5mg)

3 Contact area of ratchet and RD carriage unit (2points) G-26(3-5mg)

4 Side of shafts for sending ribbon in the carriage unit (3points) G-26(3-5mg)

5 Oil pad O-8 (0.3cc)

6 The platen gap adjustment slots on the right frame G-26(2mm width)

7 Contact area of carriage unit guide, CR G-26(3-5mg)

8 60mm from the left edge of CR guide rac k G-26(2mm width)

9 Rack parts of the CR guide (3 points) G-26(3-5mg)

10 Gear teeth of the gear18 and 36 G-26(3-5mg)

Table 6-1. Lubrication

Table 6-2. Lubrication Points

Contents

Main NOTICE Copyright 1997 by SEIKO EPSON CORPORATION Nagano, Japan PRECAUTIONS WARNING CAUTION WARNING CAUTION PREFACE Page Page Chapter 1 Product Descriptions 1.1 Specifications 1.1.1 Features Page 1.2 Hardware Specifications 1.2.1 Printing Method 1.2.2 Printing Specifications Rev. A 1- 1.2.3 Paper Handling Specifications 1.2.4 Paper Specification Rev. A 1- Note1) Note3): Note2): Note2): Page Page 1.2.5 Printable Area Rev. A 1-11 Note *1) Printable Area Printable Area BM 1.2.6 Ribbon Cartridge 1.2.7 Input data buffer Note*) 1.2.8 Electrical Specification 1.2.9 Reliability 1.2.10 Environmental Condition 1.2.11 Safety Approvals 1.2.12 CE Marking 1.2.13 Acoustic Noise 1.3 Firmware Specification 1.3.1 Control Codes and Fonts Page 1.3.2 Interface Specification 1.3.2.1 Parallel interface (Forward channel) Page 1.3.2.2 Parallel Interface (Reverse channel) Note*): Rev. A 1-21 1.3.2.3 Optional Interface 1.3.2.4 Interface Selection 1.3.3 Prevention Hosts from Data Transfer Timeout 1.4 Operation 1.4.1 Control Panel 1.4.1.1 Usual Operation Page 1.4.1.2 Switches 1.4.1.3 Indicators(LED) 1.4.1.4 Buzzer 1.4.2 Default Setting Notes. 1.4.3 Bi-d Adjustment 1.4.4 Initialization 1.4.5 Errors 1-3 1.5 Main Components 1.5.1 C214 Main Board 1.5.2 C214PSB Board Page Chapter 2 Operating Principles Rev. A 2-1 2.1 Printer Mechanism Operation 2.1.1 Printing Mechanism Page 2.1.2 Carriage Mechanism Page 2.1.3 Ribbon Advance Mechanism 2- 2.1.4 Paper Advance Mechanism 2.1.4.1 Paper Advance Mechanism 2.1.4.2 Paper Advance Detector Mechanism Page 2.1.4.3 Release Lever Mechanism Release Lever Tractor Gear Roller, PF Drive Tractor Transmission Gear 2.1.5 Platen Gap Adjustment Rev. A 2-11 2.2 Power Supply Operation 2.2.1 Power Supply Circuit 2.2.1.1 Power Supply Overview 2.2.1.2 Power Supply Circuit Operation Rev. A 2-1 2.2.2 Control Circuit 2.2.2.1 Operating Principles of the Control Circuit 2.2.2.2 EEPROM Control Circuit 2.2.2.3 System Reset Circuit 2.2.2.4 Power Off Detector Circuit 2.2.2.5 Print Head Driver Circuit 2.2.2.6 CR Motor Driver Circuit 2.2.2.7 PF Motor Driver Circuit 2.2.2.8 Operation Panel Control Circuit Page Chapter 3 Disassembly and Assembly Page 3.1 Overview 3.1.1 Precautions for Disassembling the Printer 3.1.2 Tools WARNING 3-2 3.1.3 Service Check After Repair 3.1.4 Specifications for Screws 3-4 3.2 Printer Disassembly and Assembly Figure 3-1. Disassembly Flowchart The flowchart below show you the basic order for disassembly. Before disassembling any part of the printer, note the warnings in Section 3.1.1. START 3.2.1 HOUSING, UPPER Removal 3-6 3.2.2 Printer Mechanism Removal 3.2.3 C214 MAIN Board Removal 3.2.4 C214 PSB/PSE Board Removal 3.2.5 EP-ROM Replacement CHECK POINT 3.2.6 Printhead Removal 3.2.7 Ribbon Mask Removal 3.2.8 PAPER EXIT ASSY. Removal 3.2.9 Ribbon Mask Holder Removal 3.2.10 PW Detector (Top) Removal 3.2.11 MOTOR, CR Removal 3.2.12 Carriage Assy. Removal CHECK POINT Page 3.2.12.1 RATCHET, RD Removal 3.2.13 PAPER GUIDE Removal Page Chapter 3 Disassembly and Assembly Rev. A 3-21 3-22 3.2.14 Platen Removal 3.2.15 MOTOR, PF Removal Page 3.2.19 DETECTOR, PE, FRONT Removal 3.2.20 DETECTOR, PE, REAR Removal 3.2.21 LEVER, RELEASE Removal 3.2.22 Tractor ASSY. Removal Page Rev. A 4-1 4.1 Adjustment Overview Note*2) Note*1) 4.1.1 Required Adjustments 4.1.2 Required Adjustment Tools 4.2 Adjusting and Resetting the Printer Do not rotate the platen roller during this adjustment. 4.2.1 Platen Gap Adjustment Rev. A 4- 4.2.2 Factory Setting Page Rev. A 4- 4.2.3 Bi-d Adjustment Page Page 5.1 Overview 5- 5.2 Unit Level Troubleshooting Page Page Page Page Rev. A 5- Page View A R F R L 1-24 :Wire Number C :Common Terminal T:Thermistor Terminal Note*) Rev. A 5-11 5.3 Repairing the Power Supply Circuit Board Page Page 5.4 Repairing the Main Board Page Page 5.5 Repairing the Printer Mechanism Page Page 6.1 Preventive Maintenance Page Appendix A.1 Connector Summary A- Rev. A A- A- Page Page Page Page Page Page Page Page Page A-1 Page A.5 Dimension and Weight EPSON OVERSEAS MARKETING LOCATIONS As of September, 1996