Epson 670 1.4.1.3 Indicators(LED)

Chapter 1 Product Description

Rev. A 1-2

5

1.4.1.3 Indicators(LED)

This printer displays present conditions and errors on the indicators.

Indication in normal mode

LED

Printer Status Pause

*1 Paper Out

*2 Tear Off/Bin Condensed Font

Pause On --- --- --- ---

Paper out error On On --- --- ---

Paper jam

error On Blink --- --- ---

Paper eject

error On Blink --- --- ---

Head hot Blink --- --- --- ---

Micro Adjust Blink --- --- --- ---

Tear off --- --- *3 --- ---

Bin selection --- --- *3 --- ---

Condensed --- --- --- On ---

Font selection --- --- --- --- *4

Fatal error Blink Blink Blink Blink Blink

*1 Pause (Orange)

It is on when the printer is paused, and it is off when the printer is not paused.

It blinks when the Micro Adjust function is enabled or the printer is in the head hot status.

*2 Paper Out (Red)

It is on when the printer is in the paper out status, and it is off when the printer is out of this status.

*3Tear Off/Bin (Green)

2 LEDs display the status of CSF bin selection when cut sheet is used. Only a right LED is on when

Bin1 is selected, only a left LED is on when Bin2 is selected, and both LEDs are on when the Card

mode is selected.

Both LEDs blinks when continuous paper is in the Tear-off position and both LEDs are off when

continuous paper is out of the Tear-off position.

*4Font (Green)

The status of Font selection is displayed by 3 Font LEDs.

Table 1-26. LED Indicators

Contents

Main NOTICE Copyright 1997 by SEIKO EPSON CORPORATION Nagano, Japan PRECAUTIONS WARNING CAUTION WARNING CAUTION PREFACE Page Page Chapter 1 Product Descriptions 1.1 Specifications 1.1.1 Features Page 1.2 Hardware Specifications 1.2.1 Printing Method 1.2.2 Printing Specifications Rev. A 1- 1.2.3 Paper Handling Specifications 1.2.4 Paper Specification Rev. A 1- Note1) Note3): Note2): Note2): Page Page 1.2.5 Printable Area Rev. A 1-11 Note *1) Printable Area Printable Area BM 1.2.6 Ribbon Cartridge 1.2.7 Input data buffer Note*) 1.2.8 Electrical Specification 1.2.9 Reliability 1.2.10 Environmental Condition 1.2.11 Safety Approvals 1.2.12 CE Marking 1.2.13 Acoustic Noise 1.3 Firmware Specification 1.3.1 Control Codes and Fonts Page 1.3.2 Interface Specification 1.3.2.1 Parallel interface (Forward channel) Page 1.3.2.2 Parallel Interface (Reverse channel) Note*): Rev. A 1-21 1.3.2.3 Optional Interface 1.3.2.4 Interface Selection 1.3.3 Prevention Hosts from Data Transfer Timeout 1.4 Operation 1.4.1 Control Panel 1.4.1.1 Usual Operation Page 1.4.1.2 Switches 1.4.1.3 Indicators(LED) 1.4.1.4 Buzzer 1.4.2 Default Setting Notes. 1.4.3 Bi-d Adjustment 1.4.4 Initialization 1.4.5 Errors 1-3 1.5 Main Components 1.5.1 C214 Main Board 1.5.2 C214PSB Board Page Chapter 2 Operating Principles Rev. A 2-1 2.1 Printer Mechanism Operation 2.1.1 Printing Mechanism Page 2.1.2 Carriage Mechanism Page 2.1.3 Ribbon Advance Mechanism 2- 2.1.4 Paper Advance Mechanism 2.1.4.1 Paper Advance Mechanism 2.1.4.2 Paper Advance Detector Mechanism Page 2.1.4.3 Release Lever Mechanism Release Lever Tractor Gear Roller, PF Drive Tractor Transmission Gear 2.1.5 Platen Gap Adjustment Rev. A 2-11 2.2 Power Supply Operation 2.2.1 Power Supply Circuit 2.2.1.1 Power Supply Overview 2.2.1.2 Power Supply Circuit Operation Rev. A 2-1 2.2.2 Control Circuit 2.2.2.1 Operating Principles of the Control Circuit 2.2.2.2 EEPROM Control Circuit 2.2.2.3 System Reset Circuit 2.2.2.4 Power Off Detector Circuit 2.2.2.5 Print Head Driver Circuit 2.2.2.6 CR Motor Driver Circuit 2.2.2.7 PF Motor Driver Circuit 2.2.2.8 Operation Panel Control Circuit Page Chapter 3 Disassembly and Assembly Page 3.1 Overview 3.1.1 Precautions for Disassembling the Printer 3.1.2 Tools WARNING 3-2 3.1.3 Service Check After Repair 3.1.4 Specifications for Screws 3-4 3.2 Printer Disassembly and Assembly Figure 3-1. Disassembly Flowchart The flowchart below show you the basic order for disassembly. Before disassembling any part of the printer, note the warnings in Section 3.1.1. START 3.2.1 HOUSING, UPPER Removal 3-6 3.2.2 Printer Mechanism Removal 3.2.3 C214 MAIN Board Removal 3.2.4 C214 PSB/PSE Board Removal 3.2.5 EP-ROM Replacement CHECK POINT 3.2.6 Printhead Removal 3.2.7 Ribbon Mask Removal 3.2.8 PAPER EXIT ASSY. Removal 3.2.9 Ribbon Mask Holder Removal 3.2.10 PW Detector (Top) Removal 3.2.11 MOTOR, CR Removal 3.2.12 Carriage Assy. Removal CHECK POINT Page 3.2.12.1 RATCHET, RD Removal 3.2.13 PAPER GUIDE Removal Page Chapter 3 Disassembly and Assembly Rev. A 3-21 3-22 3.2.14 Platen Removal 3.2.15 MOTOR, PF Removal Page 3.2.19 DETECTOR, PE, FRONT Removal 3.2.20 DETECTOR, PE, REAR Removal 3.2.21 LEVER, RELEASE Removal 3.2.22 Tractor ASSY. Removal Page Rev. A 4-1 4.1 Adjustment Overview Note*2) Note*1) 4.1.1 Required Adjustments 4.1.2 Required Adjustment Tools 4.2 Adjusting and Resetting the Printer Do not rotate the platen roller during this adjustment. 4.2.1 Platen Gap Adjustment Rev. A 4- 4.2.2 Factory Setting Page Rev. A 4- 4.2.3 Bi-d Adjustment Page Page 5.1 Overview 5- 5.2 Unit Level Troubleshooting Page Page Page Page Rev. A 5- Page View A R F R L 1-24 :Wire Number C :Common Terminal T:Thermistor Terminal Note*) Rev. A 5-11 5.3 Repairing the Power Supply Circuit Board Page Page 5.4 Repairing the Main Board Page Page 5.5 Repairing the Printer Mechanism Page Page 6.1 Preventive Maintenance Page Appendix A.1 Connector Summary A- Rev. A A- A- Page Page Page Page Page Page Page Page Page A-1 Page A.5 Dimension and Weight EPSON OVERSEAS MARKETING LOCATIONS As of September, 1996