Epson EMP-1825 ft Power indicator lights red

Problem Solving 70

ft Power indicator lights red

: Lit : Flashing: : Off

Status Cause Remedy or Status

Internal Error Stop using the projector, disconnect the power cable from the electrical outlet, and contact your local dealer or the nearest

address provided in the Support and Service Guide. sEpson Projector Contact List

Fan Error

Sensor Error

Stop using the projector, disconnect the power cable from the electrical outlet, and contact your local dealer or the nearest

address provided in the Support and Service Guide. sEpson Projector Contact List

High Temp Error

(overheating)

The lamp turns off automatically and projection stops. Wait for about five minutes. After about five minutes the projector

switches to standby mode, so check the following two points.

• Check that the air filter and air exhaust vent are clear, and that the projector is not positioned against a wall.

• If the air filter is clogged, clean or replace it. sp.81, 87

If the error continues after checking the points above, stop using the projector, disconnect the power cable from the

electrical outlet, and contact your local dealer or the nearest address provided in the Support and Service Guide. sEpson

Projector Contact List

When using at an altitude of 1500 m or more, set "High Altitude Mode" to "On". sp.47

Lamp Error

Lamp Failure

Lamp Cover Open

Check the following two points.

• Take out the lamp and check if it is cracked. sp.84

• Clean the air filter. sp.81

If it is not cracked _ Re-fit the lamp and turn on the power.

If the error continues _ Replace the lamp with a new lamp and turn on the power.

If the error continues _Stop using the projector, disconnect the power cable from the electrical outlet, and contact

your local dealer or the nearest address provided in the Support and Service Guide.

sEpson Projector Contact List

If it is cracked _Replace it with a new lamp, or contact your local dealer for further advice. If replacing the lamp

yourself, be careful to avoid pieces of broken glass (you cannot continue projecting until the lamp is

replaced).

Check that the lamp cover and the lamp are securely installed. sp.84

If the lamp cover or the lamp is not securely installed, the lamp does not switch on.

When using at an altitude of 1500 m or more, set "High Altitude Mode" to "On". sp.47

Abnormal

RedRedRed

RedRed

RedRed

RedRed

Contents

Main Notations Used in This Guide fSafety Indications g fGeneral Information Indications q s Contents Useful Functions Configuration Menu Troubleshooting Appendices Contents 4 Projector Features EMP-1825/1810 Common Features EMP-1825 Features fComputer and wireless connection fSimple connection with Windows Vista (Network Projector) fConnect using a USB cable (USB display) fPresentations without a computer Part Names and Functions Page Page Page Part Names and Functions 11 Page Part Names and Functions 13 H I J Remote Control A B C D E Page Useful Functions Correcting Distortion in the Projected Image q Automatically Correcting Distortion (Quick Setup) fFitting projected image properly inside the screen q Performing Manual Correction A B C q D fH/V-Keystone Changing the Projected Image q Automatically Detect Incoming Signals and Change the Projected Image (Source Search) Changing Directly from the Remote Control Functions for Enhancing Projection Selecting the Projection Quality (Selecting Color Mode) p.43 q "Image" menu from the configuration menu. Hiding the Image and Sound Temporarily (A/V Mute) q s Freezing the Image (Freeze) q Changing the Aspect Ratiog (Resize) q Pointer Function (Pointer) q A B Enlarging Part of the Image (E-Zoom) q h A B want to enlarge. q q q Setting the projector ID A configuration menu, select "Extended" - "Projector ID". s"Using the Configuration Menu" p.42 B q C Setting the ID of the projector to be operated Adjusting Color for Several Projectors (Multi-Screen Color Adjustment) Summary of Adjustment Procedure Image Correction Method A B C D E Security Functions Managing Users (Password Protect) fType of Password Protect fSetting Password Protect q A seconds. B C E fEntering the Password While holding down the [Num] button, enter the password by pressing the numeric buttons. Restricting Operation (Operation Lock) q A "Operation Lock". s"Using the Configuration Menu" p.42 B C displayed. Anti-Theft Lock fInstalling the wire lock Configuration Menu Page List of Functions Image Menu Signal Menu List of Functions 45 Settings Menu For EMP-1825 For EMP-1810 List of Functions 46 Extended Menu For EMP-1825 For EMP-1810 Page Network Menu (EMP-1825 Only) fOperations in the Network Menu fSoft keyboard operations fBasic Menu Page A select "Network Configuration", and then press the [Enter] button. B A B Page A B q Page fSecurity Menu q Page Page Page List of Functions 62 fMail Menu When this is set, if the projector enters an abnormal/warning state, you are notified by e-mail. Page Page Info Menu (Display Only) Page Troubleshooting Using the Help A p.69). B q "Problem Solving" ( Problem Solving Reading the Indicators Problem Solving 70 ft Power indicator lights red : Lit : Flashing: : Off fi o Indicator is lit or flashing orange q When the Indicators Provide No Help Problem Solving 73 fProblems relating to images f Problem Solving 74 f f Problem Solving 75 f f Problem Solving 76 f f Problem Solving 77 fProblems when projection starts f fOther problems f Problem Solving 78 f Appendices Installation Methods q W Warni ng Cleaning q Cleaning the Projector's Surface Cleaning the Lens Cleaning the Air Filter and Air Intake Vent Replacing Consumables A B Caution C Safety Instructions Replacing the Lamp fLamp replacement period A B Warni ng Caution Page F q fResetting the lamp operating time Replacing the Air Filter q A B C Saving a Users Logo q D E ^ F q Screen Size and Distance Connecting USB Devices (Digital Camera, Hard Disk Drive or Memory Devices) (EMP-1825 Only) Connecting USB Devices q Inserting and Ejecting CompactFlash Cards (EMP-1825 Only) How to Insert Cards Insert the CompactFlash card into the card slot with its top surface facing up. How to Remove Cards A B fCard Slot Access Indicator Statuses Connecting to External Equipment q Connecting to an External Monitor q Connecting to External Speakers Connecting a LAN Cable (EMP-1825 Only) To prevent malfunctions, use a category 5 shielded LAN cable. Optional Accessories and Consumables fConsumables fOptional accessories Glossary Glossary 98 ESC/VP21 Commands Command List Cable Layouts fSerial connection fCommunications protocol A B C Projector". PJLink (EMP-1825 Only) List of Supported Monitor Displays Specifications fProjector general specification Page Specifications 105 fSoftware Requirements (Only EMP-1825) The software provided with the projector runs under the following operationg environment. Page Page Appearance Index A B C D O P R S T NetNucleus WPA NetNucleus