Problems Solving | 45 | |
|
|
|
|
| : lit | : flashing | : off |
|
|
|
|
|
|
| Status | Cause | Remedy or Status |
|
|
|
|
|
|
| |
Power | Red | High temperature error | The lamp will turn off automatically and projection will stop. Wait for about 5 minutes. After |
| |
|
| (overheating) | about 5 minutes the projector will switch to standby mode, so check the following two points. |
| |
|
|
| After checking, press the [Power] button to turn the power back on. |
|
|
| Red |
| •Check that the air filter and air exhaust vent are clear, and that the projector is not positioned |
| |
|
|
| against a wall. |
|
|
|
|
| •If the air filters are blocked, clean or replace them. sp.57, p.63 |
|
|
|
|
| If this does not solve the problem and the projector continues to overheat or the indicators continue | ||
|
|
| to show a problem when the power is turned on, stop using the projector, disconnect the power cable | ||
|
|
| from the wall outlet, and contact your dealer or the nearest address provided in the "International | ||
|
|
| Warranty Conditions" section of the Safety |
| |
|
|
|
|
|
|
Power | Red | Lamp problem | Take out the lamp and check if it is broken. sp.59 |
|
|
| Red | Lamp timer failure | If the lamp is not broken, put it back in and then turn the power on. If the lamp still does not turn | ||
| Lamp cover is open | on, replace it with a new lamp. |
|
| |
|
|
|
| ||
|
|
| If this does not solve the problem, stop using the projector and disconnect the power cable from | ||
|
|
| the electrical outlet. Then contact your dealer or the nearest address provided in the "International | ||
|
|
| Warranty Conditions" section of the Safety |
| |
|
|
|
| ||
|
|
| If the lamp is broken replace it with a new lamp, or contact your local dealer for further advice. If | ||
|
|
| replacing the lamp yourself, be careful to avoid pieces of broken glass. (Projection cannot be |
| |
|
|
| carried out until the lamp is replaced.) |
|
|
|
|
|
|
| |
|
|
| Check that the lamp and the lamp cover are securely installed. If the lamp or lamp cover is not |
| |
|
|
| securely installed, the lamp will not switch on. |
|
|
|
|
|
| ||
|
|
| When using above an altitude of about 1500 m, make sure you set the "High Altitude Mode" to | ||
|
|
| "On". |
|
|
|
|
|
|
|
|
| Lamp or Temp indicator flashes orange | Warning |
| : lit | : flashing | : off | ||||
|
|
|
|
|
|
|
|
|
|
|
| Status | Cause |
|
| Remedy or Status |
|
|
|
|
|
|
|
|
|
|
| ||
| Power | Red | High temperature warning |
| (This is not an abnormality, but if the temperature rises too high again, projection will stop |
| |||
|
|
| automatically.) |
|
|
| |||
|
|
|
|
|
|
|
| ||
|
|
|
|
| •Check that the air filters and air exhaust vent are clear and that they are not up against a surface | ||||
|
| Orange |
|
| such as a wall. |
|
|
| |
|
|
|
| •If the air filters are clogged, clean or replace them. sp.57, p.63 |
|
|
| ||
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|