Manuals / Brands / Computer Equipment / Projector / Epson / Computer Equipment / Projector

Epson EMP-TW500 Replacing the Lamp, Replacing Consumables, Replacing the Air Filter, Resetting the Lamp Operating Time

1 56

Download 56 pages, 3.53 Mb

Maintenance

Replacing Consumables

Replacing the Air Filter

Dispose of used air filters properly in accordance with your local regulations.

Air filter frame:

ABS plastic

Air filter: Polypropylene

Turn off the power, wait for the cool-down period to finish (takes approximately 30 seconds), then disconnect the power cable.

Remove the air filter cover.

Put your finger under the latch. Lift up.

Replacing the Lamp

If the lamp stops working and needs to be replaced, there is the danger that the lamp may already be broken. If replacing the lamp of a projector which has been installed on the ceiling, you should always assume that the lamp is broken and handle it with extreme care during removal. Furthermore, you should stand to the side of the projector, not underneath it.

Turn off the power, wait for the cool-down period to finish (takes approximately 30 seconds), then disconnect the power cable.

*Wait until the lamp cools down (takes approximately 1 hour).

Install the new lamp.

Make sure that it faces the correct way.

Loosen the screws fixing the lamp cover.

Securely tighten the lamp fixing screws.

Resetting the Lamp Operating Time

The lamp operating time must always be reset after the lamp has been replaced with a new one.

The projector has a built-in lamp operating time counter. A replacement message is displayed when the counter reaches a certain amount.

Press	to turn on	Press	to display
the power.		the configuration menu.

42

Contents

Page About The Manuals and Notations Used Unpacking and Installation Guide Safety Instructions/World-WideWarranty Terms Setup Guide User’s Guide (this manual) Contents Features of the Projector Equipped with a wide-anglelens shift function Adjusting the hue and saturation of colours Wide range of brightness adjustments Electronic zoom and focus adjustment A variety of image setting functions Part names and Functions Remote Control •Remote control light-emittingarea •Indicator •Menu button p.23 •Memory button p.12 Rear •[Video] port Setup Guide •[HDMI] port Setup Guide HDMI ] port Appearance Basic Image Quality Adjustments Selecting the Color Mode Selecting the Image Aspect Basic Image Quality Adjustments Advanced Color Adjustments Abs. Color Temp Flesh Tone Adjustments Abs. ColorFlesh toneTempadjustment./Flesh Tone RGB Image Quality Adjustments Basic (Memory save) (Memory save) (Memory Page Configuration Menu Functions Configuration Menu "Image" menu Picture Quality Color Adjustment Color Mode *1 Memory: Standard/Advance Last Memory *1 Auto Setup *1 "Setting" menu Advanced Screen Operation User’s Logo On-ScreenDisplay Input Signal Language "Reset" menu Lamp-HoursReset Memory Reset All Reset Using the Configuration Menus Displaying a menu Selecting a menu item Changing settings When setting is complete Preparation for Using Cinema Color Editor Uninstalling Cinema Color Editor Select Uninstall Click [Uninstall] Connecting to a Computer Connection using a network cable Connection using a USB cable or RS-232Ccable Connection settings at the projector (when using a network connection) Use and to select the item to be set, and then press Setting details Using Cinema Color Editor Starting Cinema Color Editor Click to go to picture Adjusting picture quality Operating the projector Saving adjustments/LoadingSavingadjustmentstments/Loadingfrom file adjustments from a file Saving customised settings into memory Saving adjustment values into memory into a memorySavingarea customised settings into memory Retrieving saved memory settings Click the "Standard" or "Advance" tab to select the type of memory Saving projector memory settings into a computer as a memory data file Loading memory data files from a computer into projector memory Changing a memory area names Problem Solving Internal problem Sensor Lamp problem Standby mode Projection in progress Warm-upin progress Cool-downin progress Problems relating to images Have you pressed the [Power] button Was the indicator lit orange Are the cables connected correctly Has the correct video input port been selected Are the image signals being Is an extension cable being used Have the "Sync." and "Tracking" settings been adjusted correctly Has the image Contrast Has the colour been adjusted Have the colour intensity and tint been adjusted correctly? colour and tint Only when projecting images from a video source Problems when projection starts Is "Operation Button Lock" set to "ON indicator lit orange Do the indicators turn off and Problems with network connections Are the projector and the computer correctly connected to the network Has the projector been set up Maintenance Consumable Replacement Periods Air Filter Replacement Period Lamp Replacement Period Appendix Replacing Consumables Replacing the Air Filter Replacing the Lamp Resetting the Lamp Operating Time Page Optional Accessories List of Supported Monitor Displays Specifications Compatible computers for using Cinema Color Editor RS-232Ccable layout DECLARATION of CONFORMITY FCC Compliance Statement For United States Users WARNING Glossary Page Index Page General Notice: