Epson EMP-TW520, EMP-TW600 Replacing the lamp

Maintenance

Replacing the lamp

cCaution:

If the lamp stops working and needs to be replaced, there is the danger that the lamp may already be broken.

If replacing the lamp of a projector which has been installed to the ceiling, you should always assume that the lamp is broken and handle it with extreme care during removal. Furthermore, you should stand to the side of the projector, not underneath it.

1 Press or to turn the power off, wait until the projector cools down, and then turn off the main power switch.

*Wait until the lamp cools down (takes approximately 1 hour).

3 Loosen the lamp fixing screws.

2 Remove the lamp cover.

2

1

4 Remove the old lamp.

Pull out straight.

5 Insert the new lamp.

Make sure that it faces the correct way.

6 Securely tighten the7 Install the lamp cover. lamp fixing screws.

2	1

cCaution: • Install the lamp and the lamp cover securely. The lamp will not turn on if the lamp or the lamp cover is not installed correctly.

•This product includes a lamp component that contains mercury (Hg).

Please consult your state and local regurations regarding disposal or recycling. Do not put in the trash.

Appendix

45

Contents

Page About the Manuals and Notations Used Types of Manual Notations used in this User’s Guide General information Meaning of "unit" and "projector Checking the Components Documentation Table of Contents Installing the Projector Basic Operations Image Quality Adjustments Configuration Menu Troubleshooting Appendix Features of the Projector Image apperance can be selected to match the projection environment (Color Mode) Sophisticated colour adjustment Equipped with a wide-anglelens shift function Equipped with 1.5x short throw zoom lens Advanced image quality adjustment functions A variety of image setting functions Part Names and Functions Front / Top Control panel Remote control Rear Base Appearance Setting up Adjusting the projection size Lens shift adjustment Projection Methods Connecting Image Sources Preparing the Remote Control Inserting batteries into the remote control Using the remote control Projecting Images Turning the power on and projecting images 3 ON When the expected images are not projected Turning the power off Adjusting the Projection Screen Correcting projector tilt Correcting keystone distortion (Keystone) Displaying a test pattern Basic Image Quality Adjustments Selecting the colour mode Selecting the aspect Advanced Colour Adjustments Skin tone adjustment Absolute colour temperature adjustment Gamma adjustment ■Adjusting from the gamma correction values ■Customized ("Adjust it from the image") ("Adjust it from the graph") RGB adjustment (Offset, Gain) ■Offset ■Gain Hue and saturation adjustment ■Hue Examining Image Quality Further Sharpness (Advanced) adjustment Auto Iris (automatic aperture) setting Viewing Images at a Preset Image Quality (Memory Function) Retrieving image quality adjustments (Load Memory) Saving image quality adjustments (Save Memory) Configuration Menu Functions List of configuration menus Configuration Menu "Picture" menu Color Mode*1 Input Adjustment *2 Color Saturation *2 Tint *2 "Image" menu Aspect *1 Zoom Caption *1 Tracking *1 Sync.*1 Position *1 Advanced Auto Setup "Settings" menu Keystone Operation User’s Logo Display Input Signal Projection Language "Memory" menu Save Memory Load Memory Reset Memory "Reset" menu Reset All Reset Lamp Hours Using the configuration menus 1 Displaying a menu Problem Solving Reading the indicators When the (warning) indicator is lit or flashing warning/problem When the (operation) indicator is lit or flashing normal When the indicators provide no help Problems relating to images ■The message "Not Supported." is displayed ■The message "No Signal." is displayed ■Images are fuzzy or out of focus ■Interference or distortion appear in images ■Image is truncated (large) or small ■ Image colours are not right ■ Images appear dark Problems when projection starts Problems with the remote control Maintenance Cleaning Cleaning the air filter Cleaning the projector case Cleaning the lens Consumable replacement periods Air filter replacement period Lamp replacement period Replacing consumables Replacing the air filter Replacing the lamp Resetting the lamp operating time Optional Accessories / Consumables List of Supported Monitor Displays Component Video Composite Video/S-Video Analog-RGBsignals/signals input to the [HDMI] input port Specifications ■Angle of tilt ■RS-232Ccable layout DECLARATION of CONFORMITY FCC Compliance Statement For United States Users WARNING Glossary Page Index Page General Notice: