Problem Solving

■The message "Not Supported." is displayed

Are the image signal format

If a composite video

 

or S-Video is being input

settings correct?

If projection does not occur when the "Video Signal" menu

 

 

 

command is set to "Auto", select the signal format that matches the

 

 

 

signal source.

 

 

 

 

 

s "Settings" - "Input Signal" - "Video Signal" page 33

 

 

 

 

 

 

 

 

If the signal source is connected to the [InputA] port

 

 

 

If projection does not occur when the "InputA" in the "Input

 

 

 

Signal" menu command is set to "Auto", set the signal format that

 

 

 

matches the signal that is being projected from the connected

 

 

 

equipment. s "Settings" - "Input Signal" - "Input A" page 33

 

 

 

You can also press

 

, on the remote control to select the

 

 

 

 

 

 

 

 

 

 

 

format. s page 15

 

 

 

 

 

 

 

Does the mode match the

Use the "Resolution" menu command to check the signals being

frequency and resolution of the

input, and check the "List of Supported Monitor Displays" to make

image signals?

sure that the signals are compatible.

 

 

 

s "Info" - "Resolution" page 27

 

Only when projecting

 

 

 

s "List of Supported Monitor Displays" page 48

 

computer images

 

 

 

 

 

 

 

 

 

 

 

 

 

■The message "No Signal." is displayed

Are the cables connected

Check that all of the cables required for projection are securely

correctly?

connected. s page 12

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Has the correct video input port

Press

 

,

 

,

,

or

on the remote control or

 

 

 

 

been selected?

on the projector’s control panel to change the image source.

 

 

 

s page 15

 

 

 

 

 

 

 

 

 

 

 

 

Is the power for the connected

Turn the power on for the devices.

 

equipment turned on?

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Are the image signals being

If the image signals are only being output to the computer's LCD

output to the projector?

monitor, you need to change the output.

 

 

 

 

For some computer models, when the image signals are output

 

Only when projecting

 

 

 

externally, they no longer appear on the LCD monitor.

 

images from a laptop

 

 

 

s Computer documentation, under a title such as "External

 

computer or computer

 

 

 

output" or "Connecting an external monitor"

 

with a built-in LCD

 

 

 

 

 

 

 

 

 

 

 

 

screen

 

If the connection is made while the power is already turned on, the

 

 

 

function [Fn] key that switches the computer's video signal to

 

 

 

external output may not work. Turn the power for the projector and

 

 

 

the computer off and then back on again. s page 14

 

 

 

 

 

 

 

 

 

 

 

■Images are fuzzy or out of focus

Has the focus been adjusted

Adjust the focus. s page 16

correctly?

 

 

 

Is the lens cover still attached?

Remove the lens cover.

 

 

Is the projector at the correct

The recommended distance from the projector to the screen is

distance?

within 88-1365 cm (2.9-44.8 ft.) for a screen size of 16:9, and 107-

 

1671 cm (3.5-54.8 ft.) for a screen size of 4:3. Set up the projector

 

so that the projection distance is within this range. s page 10

 

 

Is the keystone adjustment

Decrease the projection angle to reduce the amount of keystone

value too large?

correction. s page 17

 

 

38