AE/LZB 119 1902 R1A

Digital I/O Lines

The balanced RxIF and RxIF_B (B implies “Barred” indicating that the condition is true when the line is low) lines connect through resistor and capacitor RF decoupling circuits to HILLARY D701. RxIF connects through resistors R715 and R714 and capacitor C707 to D701, Pin 8. RxIF_B connects through resistors R717 and R718 and capacitor C709 to D701, Pin 7. Both of these lines connect to a Phase Digitizer internal to D701.

Phase Digitizer (D701)

The phase digitizer demodulates the 450 kHz IF to recover the digitized receive audio. The output of the phase demodulator is connected to Rx DSP Interface (Refer to Schematic Diagram, Sheet 13). The Rx DSP Interface output of D701 connects to the DSP module through D701, Pin 69 (RXSIF_DSPDATA), Pin 73 (RXSIF_DSPCLK) and Pin 74 (RXIF_DSPSYNC). DSP interface lines connect to DSP TDR (TDM DATA RX), DSP TCKDR (TDM CLOCK RX) and DSP TRSR (TDM FRAME SYNC TX) respectively. These lines can be metered on the DSP module at test points TP8 (data), TP15 (clock) and TP14 (sync), respectively.

DSP Module

The Digital Signal Processing (DSP) Module does all the Channel Guard filtering, provides squelch, audio mute, 1.5, 3, and 4.5 dB of volume attenuation and changes the digitized audio into an analog signal. The output of the DSP module is on X21-17 (PCM_DSEAR). This output can be metered at test point TP3 on the DSP module.

Host Interface

The PCM_DSPEAR line connects to D701, Pin 64 and goes to the PCM/DSP HOST INTERFACE. The audio output of D701 is on Pin 40 (PCM_CDCEAR) and connects to D601, Pin 34 (DPCI).

DEBBIE (D601)

This signal (PCM_CDCEAR) is then put through a decoder, low pass filter, volume control circuit and an amplifier. The low pass filter, filters out an 8 kHz sample rate. The volume control provides 24 dB in 6 dB steps. The output of D601 is on Pin 22 (RXAUDIO). The signal can be metered at test point TP601. At maximum volume there should be 350 mVolts RMS (1.0VP-P) with a 1 kHz tone and 3 kHz deviation.

Operational Amplifier (N300)

This signal (RXAUD1) connects through capacitor C611 and resistor R625 to operational amplifier N300, Pin 6 (-B). Feedback for the amplifier is through resistor R627. The gain of this amplifier is changed by the RX_VOL_ATTN line (D701, Pin 116) to provide a total of 48 dB of volume control attenuation. This is accomplished by the RX_VOl_ATTN line going high, causing transistor V604-1 to conduct and connecting 10k ohms resistor R626 across 68k ohms resistor R627 to reduce the gain of N300B. The output of this amplifier is on Pin 7 (RXAUD2).

Audio Power Amplifier (N600)

This signal is attenuated through resistor R629 then coupled through coupling capacitor C613 to audio power amplifier N600A, Pin 7 (+IN). This signal is also connected through resistor R628 and coupling capacitor C612 to the Universal Device Connector (UDC_AUDIO_OUT). The audio input to N600A can be metered at test point TP602 and at maximum volume should be 250 mVP-P. The input will be 21 mV RMS (60 mVp-p) to produce 500 mWatts output into 16 ohms. Power amplifiers N600A and N600B provide differential outputs on Pin 1 (+OUT) which is AUDIO_PA_HI and Pin 3 (+OUT) which is SPK_LO. The bridged output of these two lines provides 2.83 V RMS for 500 mWatts output into 16 ohms. The SPK_LO line connects through the flex circuit to the low side of the speaker. The AUDIO_PA_HI connects through resistor R641 to the other side of the speaker (SPKR_HI). Resistor R641 is used to attenuate the speaker audio during duplex operation. Normally MOSFET V602 is turned on, by- passing R641 to get the full volume to the speaker. V602 is controlled by a binary output line from HILLARY labelled DUPLEX_SPKR_ATTEN. When this line is at 0 volts, transistor V603 is off and the collector is high which turns on both V602 MOSFETs, by-passing R641. SPKR_HI then connects through the flex circuit to the high side of the speaker. Two series MOSFETS are used to prevent forward biasing the characteristic diodes across the MOSFETS with audio when the MOSFETS are OFF.

12

Page 12
Image 12
Ericsson LPE-200 manual Digital I/O Lines, Phase Digitizer D701, DSP Module, Host Interface, Operational Amplifier N300