Manuals / EverFocus / Car Audio and Video / Car Stereo System

EverFocus EDR410H, EDR810H, EDR810M, EDR410M instruction manual Call Monitors

Models: EDR410M

1 150

Download 150 pages 37.71 Kb

Page 25

8.Call Monitors

Connect the call monitor output connectors to a call monitor. The call monitor display selected live cameras in full screen format.

Note: The call monitor will only display one full screen camera at a time.

Image 25

EverFocus EDR410H, EDR810H, EDR810M, EDR410M instruction manual Call Monitors

Contents

EDR810H/EDR810M EDR410H/EDR410M VolumeInstruction Manual Release Date April EDR 810H/810M/410H/410M Instruction GuideFederal Communication Commission Interference Statement Page 2. INSTALLATION TABLE OF CONTENTS3. DVR MENU SETUP 1. PRODUCT OVERVIEW5. PLAYBACK OVERVIEW APPENDIX B ALARM BOARD CONFIGURATION APPENDIX A REMOTE CONTROLTROUBLESHOOTING Safety Warning Safety Precautions Safety Precautions Chapter 1.1 Features1. Product Overview 1.2 Specifications 4 CH4 / PLAY Play Back 1.3 Front Panel Keypads14 CALL Press this key to enter and set up CALL MENU 12 SEQ Press this key to enter the auto sequential switching modeJog Dial Shuttle and Jog Dial ShuttleBack panel of 810H 1.4 Back Panel ConnectionsBack panel of 410H POWER RS232 Wireless LANRS485 RemoteFor mobile model only 1.5 Monitor DisplayPage Play Date 4. Current time 3. Event5. HDD/FAN status 6 GPS orientationChapter 2. InstallationI PACKING II SYSTEM FLOORPLAN1. Power 2.1 Basic Wiring Instructions2. Cameras 3. Audio Input8. Call Monitors 2.3 Final Install Process 2.2 Hard Disk Drive InstallationDiagram 2.2 shows 3.5“ Hard Drive Quick Installation Guide 2.4 QUICK INSTALLATION GUIDE FOR EDR810M & EDR410M ONLY The DVR can be mounted horizontally suspend or support mounted  Equipment Required  Unpack EverythingPage Passenger seat underneath Drive seat between seat and wall Trunk Users are suggested to use “suspend” for mounting option Installing the Cameras and Monitor Chapter 3. DVR Menu Setup3.1 Time/Date Setup Menu 6. START TIME To set the beginning of daylight saving time a Go to a PC that is connected to the internet Diagramb Click on “START” - “RUN” - type “cmd” and press “OK” Atlantic Daylight Time subtract 3 hours from GMTHawaii-Aleutian Daylight Time subtract 9 hours from GMT Alaska Standard Time subtract 9 hours from GMTHawaii-Aleutian Standard Time subtract 10 hours from GMT WEEK3.2 Camera Setup Menu 4. SEQ MAIN/CALL Set the number of seconds a camera is displayed in sequence. The first number is for sequence on the Main Monitor, the second number is for sequence on Call Monitor ACTION 6. REC SPEED & ACTION7. SUMMARY 1. RECORD AUDIO 3.3 Record Setup Menu2. TIME STAMP 3. TIME STAMP POSITION8. PRE-ALARM RECORDING 6. RECORD MODE4. WATER MARK 9. RELAY OUT3.4 Alarm Setup Menu 3. LOG NONE = not activated, 1 = output signal 1 transmitted 8. ALARM EMAIL6. DURATION 10. ALARM NETWORK YES Enable alarm network. NO Disable alarm network 3.5 Motion Setup Menu 7. ALARM NETWORK 6. ALARM EMAIL9. MOTION DELAY MENU 1. VIDEOLOSS 3.6 VIDEOLOSS Setup Menu2. LOG 7. ALARM NETWORK YES Enable alarm network. NO Disable alarm network 3.7.1 CONFIG 3.7 Network Setup Menu3. SUBNET MASK 2. IP Address4. GATEWAY 5. DNS SERVER11. MAC ADDR 10. BW CONTROL3.7.2 ALARM NETWORK In the EMAIL of the NETWORK SETUP MENU, we define 3.7.3 EMAIL3. AUTHENTICATION 1. SMTP SERVERIn the PASSWORD of the NETWORK SETUP MENU, we define 3.7.4 PASSWORD7. SENDER EMAIL ADDR In the WIRELESS of the NETWORK SETUP MENU, we define 3.7.5 WIRELESS7. AUTHENTIFICATION Select from OPEN/NONE, OPEN/WEP, SHARED/NONE, SHARED/WEP or10. NETWORK TYPE In the PPPoE of the NETWORK SETUP MENU, we define 3.7.6 PPPoEIn DDNS of the NETWORK SETUP MENU, we define 3.7.7 DDNS4. RECORD ID Record ID EVERFOCUS DDNS 3.7.8 GPS Minutes 00 ~ 3.8 Schedule Setup MenuMinutes 00 ~ 2. DISK VIDEO DELETE Press SELECT to start delete 3.9 Disk Setup MenuPage 3.10 Control Setup Menu ED2200/2250 RS4853.11.1 FAN FAULT 3.11 Warning Setup Menu4. NETWORK ALARM 3.11.2 HDD TEMP5. SEND EMAIL 7. SET TEMPERATURE 4. NETWORK ALARM5. SEND EMAIL 6. STOP RECORD4. NETWORK ALARM 3.11.3 NO HDD5. SEND EMAIL 3.11.4 HDD FULLYES To enable network alarm NO To disable network alarm 4. NETWORK ALARMYES Send an email when HDD is full NO Will not send an email when HDD is full3. LOAD/SAVE CONFIGURATION 3.12 System Setup Menu7. SYSTEM PASSWORD ENABLE 2 Delete disk in Disk Setup MenuUser Level and Right 4. Recording Overview 4.1 Instant N Recording SetupChapter 4.2 Schedule Recording Setup 4.3 Event Recording Setup 2. When the event is set, enter the CAMERA SETUP MENU to set the event recording speed IPS of the camera for TP N Instant Recording or TP 1~8 Schedule Recording 1. If you only want to record event motion or alarm activity ONLY, set the normal record speed as 0 IPS in the CAMERA SETUP MENU 5.1 Basic Playback 5. Playback OverviewChapter 4 Slow Forward/Reverse Playback 3 Fast Forward/Reverse PlaybackPress PAUSE key to freeze the picture 5 Image advance Forward/ReverseTurn the Jog dial clockwise to advance the still video image by image The field feed speed will increase if the Jog dial is turned quicklyIn the SEARCH MENU 5.2 Search Playback1 TIME / DATE Search Playback Lastly, press SELECT to start search PL a Power Loss event An an Alarm event, n = input numberRTn a power Return event in a schedule recording mode, n = TP 1~8 RTN a power ReTurn event in Normal/instant recording modeChapter 6. Copying Video6. DEVICE 5. SIZE OF SELECTED IMAGE MB PRESS PLAY TO ESTIMATE6.1 Viewing a Copied File Chapter 7. Call Overview“ON” or “OFF” 4. QUAD DISPLAYChapter 8. Screen Display Setting & Mode5. SHARPNESS 8.1 Mode Button Chapter 9. Upgrade Firmware10.1 Introduction to TCP/IP 10. Networking Overview10.2 Subnet Masks Chapter10.3 Gateway Address 10.5 Pre-Installation10.4 Virtual Ports Who is your Internet provider? 10.6 What Type of Network Connection do you have? Connection Procedure 10.7 Simple One to One ConnectionCrossover Ethernet Cable Pin outs  To assign a static IP address in windows 2000/XP Page Page Page http//192.168.1.3 Internet 10.8 Direct High Speed Modem ConnectionHi-speed modem Cat Straight Through Cable DVRPage Straight Through Ethernet Cable Pin outs 10.9 Router or LAN ConnectionConnection Procedure Page Chapter 11. Linksys Port ForwardingSample Screen Dynamic DNS Status - This displays the status of the DDNS connection Chapter 12. D-Link Port ForwardingExample1 Virtual Server - Select Enabled or DisabledDynamic DNS  Then enter the hostname you created with DynDNS.org  Then enter the username and password you use to log into DynDNS.orgExample Everfocus.homeip.net Chapter 13. EverFocus DDNS SetupEverFocus DDNS server Example http//hostname.everfocusddns.com Chapter 14. Viewing through Internet ExplorerNote This section is only necessary if you DO NOT see the yellow Enabling ActiveX ControlsActiveX bar at the top of your browser screen “Disable” “Enable”“Prompt” Main Screen 8. Types of events to be searched Alarm, Motion and/or Vloss 2. STOP Press this key to stop Playback and return to Live mode11. Press “Update” to refresh the event list The followings are a brief description for each of the icons24. Relay Output Press the button to trigger relay output 14.1.1 Search by Time 14.1 SEARCH14.1.2 Search by EVENT 14.2 PTZ control 14.3 REMOTE ARCHIVE 3 Enter Month, Day, Hour, Minute, and Second directly in display bar 7. Press STOP button if you wish to cancel archiving4 Press OK to select time archiving file at same timeII. Select “Run” or “Save” the file I. Press Download DVRViewer button1. Load File load an archived EDR MPEG File .arv Detailed explanation of DVRViewer is as follows2. Stop stop playback 3. Play play video 4. Step move the paused image one step backwardPage 14.4 Remote Configuration 6. Finally, click Apply to confirm setting DATE/TIME setup menu Set Date/Time Manually2. Click “” to decrease Year value, “” to increase Year value 3. Click “” to decrease Month value, “” to increase Month valueCAMERA setup menu RECORD setup menu ALARM setup menu 4. The selected area will switch to the opposite color MOTION setup menu Set Motion Grid5. Click Apply to save the changes VIDEO LOSS setup menu 3. Drag the mouse to highlight the desired areaNETWORK 2 setup menu NETWORK 1 setup menuSCHEDULE setup menu CONTROL setup menu WARNING setup menu SYSTEM setup menu 15.1 Transmission Setting 15. Interface SpecificationsChapter 15.2 Remote Control Protocol ID = SELECT 2-5. Checksum ByteAppendix Appendix A Remote ControlAppendix Appendix B Alarm Board ConfigurationNAME PIN #ALMRSTO REC-IN The DVR will not go into record mode? Troubleshooting The DVR displays no picture?  There is no display coming from one of the channels on the DVR?Head Office EverFocus Electronics CorpUSA Office USA N.Y. Office