Exmark Lazer Z XP manual Dimensions, Torque Requirements, minimum125 ft-lbs. 169 N-m

2.10.8Cutting Height Adjustment: an extra-long cushioned lever is used to adjust the cutting height from 1 1/2” (3.8 cm) to 5” (10.2 cm.) in 1/4”(6.4 mm) increments. The cutting height adjustment handle has a transport position and all adjustments can be made while the operator remains seated. Units also have a foot operated deck lift assist lever to aid in raising the deck.

2.10.9Mulching Kit: Optional.

2.11DIMENSIONS

2.11.1 Overall Width:		without deck	deflector up	deflector down
	60” Deck	54.5 in. (138.4 cm)	61.4 in. (156.0 cm)	72.2 in. (183.4 cm)
	72” Deck	58.5 in. (148.6 cm)	73.2 in. (185.9 cm)	84.3 in. (214.1 cm)
2.11.2 Overall Length:		Roll Bar – Up	Roll Bar - Down
	60” Deck	82.2 in. (208.8 cm)	92.3 in. (234.4 cm)
	72” Deck	86.0 in. (218.4 cm)	96.1 in. (244.1 cm)
2.11.3 Overall Height:
		Roll Bar - Up	Roll Bar - Down
	60” Deck	73.7 in. (187.2 cm)	55.6 in. (141.2 cm)
	72” Deck	73.7 in. (187.2 cm)	55.6 in. (141.2 cm)
	NOTE: Height will vary slightly depending on seat setting
2.11.4 Tread Width: (center to center of tires, widthwise)
		Drive Wheels	Casters
	60” Deck	42.8 in. (108.7 cm)	38.9 in. (98.8 cm)
	72” Deck	46.8 in. (118.9 cm)	47.6 in. (120.9 cm)
2.11.5 Wheel Base: (center of caster to center of drive tire)
	60” Deck	54.0 in. (137.2 cm)
	72” Deck	56.8 in. (144.3 cm)
2.11.6 Curb Weight:
	60” Deck	1639 lbs. (743 kg)
	72” Deck	1657 lbs. (752 kg)

2.12 TORQUE REQUIREMENTS

Bolt Location	Torque
Cutter Housing Spindle Nut (secured with threadlocker)	140-145 ft-lbs. (190-197 N-m)
Blade Mounting Bolt	115-120 ft-lbs. (156-163 N-m)
Jack Shaft Spindle Nut	75-80 ft-lbs. (102-108 N-m)
Engine Deck/Front Frame Mount	30-35 ft-lbs. (41-48 N-m)
Anti-Scalp Roller (See Figure 12)
Type A – Whizlock Nut	40-45 ft-lbs. (54-61 N-m)
Type B – Nyloc Nut	30-35 ft-lbs. (41-47 N-m)
Type B – Hex Capscrew	50-55 ft-lbs. (68-75 N-m)
Starter Mounting Bolts (M10)	22-27 ft-lbs. (30-37 N-m)
Water Separator Mounting Bolts (M8)	11-14 ft-lbs. (15-19 N-m)
Hydraulic Oil Filter Head Mounting Bolts (M6)	60-72 in-lbs. (7-8 N-m)
Wheel Lug Nuts	90-95 ft-lbs. (122-129 N-m)
Wheel Motor Mounting Bolts	72-77 ft-lbs. (98-104 N-m)
Wheel Hub Slotted Nut	minimum125 ft-lbs. (169 N-m)
Rollover Protection System (Roll Bar) Mounting Bolts ....	30-35 ft-lbs. (41-47 N-m)
Clutch Retaining Bolt (secured with threadlocker)	55-60 ft-lbs. (75-81 N-m)

- 13 -