Extron electronic MTP 15HD RSA manual Sync PowerCage MTP T 15HD RSA, PowerCage MTP R 15HD RSA SEQ

Sync — PowerCage MTP T 15HD RSA, PowerCage MTP R 15HD RSA SEQ

Input/output type	RGBHV, RGBS, RGsB, RsGsBs
Standards	NTSC 3.58, NTSC 4.43, PAL, SECAM
Input level (transmitter)	3.5 V to 5.5 Vp-p, unterminated
Output level (receiver)	4.0 V to 5.0 Vp-p, unterminated
Input impedance (transmitter)	573 ohms ±5%
Output impedance (receiver)	110 ohms
Polarity
Transmitter	Positive or negative (follows input polarity)
Receiver	Positive or negative (switch-selectable)

Audio — PowerCage MTP T 15HD RSA, PowerCage MTP R 15HD RSA SEQ

Number/signal type	1 set of proprietary analog signals
Connector	1 female RJ-45
Gain	Unbalanced output: 0 dB; balanced output: +6 dB
Frequency response	20 Hz to 20 kHz, ±1 dB
THD + Noise	0.15% @ 1 kHz, 0.3% @ 20 kHz at nominal level
S/N	>70 dB at maximum output (unweighted)
Stereo channel separation	>60 dB @ 1 kHz
CMRR	>43 dB @ 20 Hz to 20 kHz

Audio input — PowerCage MTP T 15HD RSA

Number/signal type	1 stereo, unbalanced
Connector	(1) 3.5 mm captive screw connector, 5 pole
Impedance	>10k ohms, unbalanced
Nominal levels	+4 dBu (1.23 Vrms), -10 dBV (316 mVrms)
Maximum level	+18 dBu, (unbalanced) at 1% THD+N

NOTE: 0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu

Audio output — PowerCage MTP R 15HD RSA SEQ

Number/signal type	1 mono, balanced/unbalanced
Connector	(1) 3.5 mm captive screw connector, 5 pole
Impedance	50 ohms unbalanced, 100 ohms balanced
Gain error	±1 dB channel to channel
Nominal levels	+4 dBu (1.23 Vrms), -10 dBV (316 mVrms)
Maximum level	+18 dBu, unbalanced at 1% THD+N

Control/Remote

Serial ports
Boards	Pass-through, uni- or bidirectional Input/output: 1 set of proprietary signals on female
	RJ-45 jack
	Output/input: 1 RS-232 via 3 poles of a 3.5 mm captive screw connector (3 pole for
	transmitter, 5 pole for receiver)
Baud rate and protocol
Boards
Baud rates	Up to 38400 bps at up to 600 ft (185 m). Higher data rates and distances are possible.
	Performance varies based on baud rate and cable length.)
Protocol	Data bits = 5 - 8
	Stop bits = 1 or 2
	Parity = odd, even, none
	Flow control = XON, XOFF, none
	Defaults: 8 data bits, 1 stop bit, no parity

NOTE: For PowerCage MTP boards, protocol is mirrored between the transmitter and the receiver.

Serial control pin configurations
Captive screw connector
Boards	Transmitter: 1 = Tx, 2 = Rx, 3 = GND
	Receiver: 3 = GND, 4 = Tx, 5 = Rx
Mini stereo jack	RS-232: tip = Tx, ring = Rx, sleeve = GND
PowerCage MTP T 15HD RSA and PowerCage MTP R 15HD RSA SEQ • Reference Information		13