Extron electronic MTP R 15HD RSA D user manual Reference Information, Specifications

Reference Information

Specifications

Video

Gain	Unity
Number/signal type	1 set of proprietary analog signals
Connectors	1 female RJ-45 on a pigtail

Video input — See MTP Series Transmitters' video output specifications.

Video output

Number/signal type	1 analog VGA-UXGA RGBHV, RGBS,
	RGsB, RsGsBs, HD component video,
	component video, S-video, or composite
	video
Connectors	1 female 15-pin HD
Nominal level	1 Vp-p for Y of component video and
	S-video, and for composite video
	0.7 Vp-p for RGB and for R-Y and B-Y of
	component video
	0.3 Vp-p for C of S-video
Minimum/maximum levels	0.3 V to 1.45 Vp-p
Impedance	75 ohms
Return loss	<-30 dB @ 5 MHz
DC offset	<±20 mV with input at 0 offset

Sync

Output type	RGBHV, RGBS, RGsB, RsGsBs
Standards	NTSC 3.58, NTSC 4.43, PAL, SECAM
Output level	4.0 V to 5.0 Vp-p, unterminated
Output impedance	110 ohms
Polarity	Positive or negative (switch selectable)

Audio

Number/signal type	1 set of proprietary analog signals from an
	MTP transmitter
Connector	1 female RJ-45
Gain	Unbalanced output: 0 dB;
	balanced output: +6 dB
Frequency response	20 Hz to 20 kHz, ±1 dB
THD + Noise	0.15% @ 1 kHz, 0.3% @ 20 kHz at nominal
	level

S/N	>70 dB at maximum output (unweighted)
CMRR	>43 dB @ 20 Hz to 20 kHz

Audio output

Number/signal type	1 mono, balanced/unbalanced
Connector	(1) 3.5 mm captive screw connector, 5 pole
	(uses 3 poles)
Impedance	50 ohms balanced, 100 ohms balanced
Gain error	±1 dB channel to channel
Nominal level	+4 dBu (1.23 Vrms), -10 dBV (316 mVrms)
Maximum level	>+14 dBu, unbalanced at 1% THD+N

Control/remote — external device (pass-through, unidirectional or bidirectional)

Serial control port input/output. 1 set of proprietary signals on a female RJ-45 jack

Serial control port output/input. RS-232 via 3 poles of a 3.5 mm captive screw connector, 5 pole

NThe serial communications link is unidirectional only, transmitter to receiver, unless the receiver's directional DIP switch has been repositioned. The switch should be repositioned only when the receiver is the only one in the system.

Baud rates	Up to 38400 bps at up to 1000' (300 m)
	(Higher data rates and distances are
	possible. Performance varies based on
	baud rate and cable length.)
Protocol	Data bits = 5 through 8
	Stop bits = 1 or 2
	Parity = odd, even, none
	Flow control = XON, XOFF, none

NProtocol is mirrored between the transmitter and the receiver.

Serial control pin configurations. Captive screw connector: 1 = TX, 2 = RX, 3 = GND

General

Recommended cable type	CAT 5/5E/6 (shielded or unshielded)
External power supply	100 VAC to 240 VAC, 50/60 Hz, external;
	to 12 VDC, 2 A, regulated
Power input requirements	12 VDC, 0.5 A

A-2 MTP R 15HD RSA D • Reference Information MTP R 15HD RSA D • Reference Information A-3