Manuals / Enterasys Networks / Computer Equipment / Computer Hardware

Enterasys Networks 7S4280-19-SYS manual Regulatory Compliance, MGBIC-02 Specifications 1000BASE-T

Models: 2S4082-25-SYS 7S4280-19-SYS

1 108

Download 108 pages 63.46 Kb

Page 100

NAC Controller PEP 7S4280-19 Specifications

MGBIC-02 Specifications (1000BASE-T)

Table A-20 MGBIC-02 / Specifications

Item	Specification

Supported Cable
Type:	Copper, Category 5 UTP
Maximum Length	Up to 100 meters

Connector	RJ45

Data Rate	1 Gbps, IEEE 802.3:2000 compatible
	1000BASE-T operation only
	Automatic crossover detection

TX Output impedance	100 ohms, typical at all frequencies between 1 MHz and 125 MHz

RX Input impedance	100 ohms, typical at all frequencies between 1 MHz and 125 Hz

Regulatory Compliance

The 2S4082‐25 and 7S4280‐19 meet the safety and electromagnetic compatibility (EMC) requirements listed in Table A‐21:

Table A-21 Compliance Standards

Regulatory Compliance	Standards

Safety	UL 60950, CSA C22.2 No. 60950, 2006/95/EC, EN 60950, IEC
	60950, EN 60825, 21 CFR 1040.10.

Electromagnetic Compatibility (EMC)	47 CFR Parts 2 and 15, CSA C108.8, 2004/108/EC, EN 55022, EN
	61000-3-2, EN 61000-3-3, EN 55024, AS/NZS CISPR 22, VCCI
	V-3.

A-10 Specifications and Regulatory Compliance

Image 100

Enterasys Networks 7S4280-19-SYS, 2S4082-25-SYS manual Regulatory Compliance, MGBIC-02 Specifications 1000BASE-T

Contents

Enterasys Page Page Regulatory Compliance Information Electromagnetic Compatibility EMC Supplement to Product Instructions Vcci Notice Enterasys NETWORKS, INC. Firmware License Agreement Vii Viii Contents NAC Controller PEP Installation TroubleshootingAppendix a Specifications and Regulatory Compliance Initializing the NAC Controller Index Figures Tables MGBIC-08 Xiv About This Guide How to Use This GuideWho Should Use This Guide Related Documents For Refer to Typographical Conventions Commonly Used Acronyms Getting Help Introduction Overview N1-7C111 Chassis NAC Controller PEP Overview 2S4082-25 NAC Controller PEP 2S4082-25 NAC Controller PEP 7S4280-19 NAC Controller PEP 7S4280-19 NAC Controller PEP Redundant Power Supplies Power Supply Lanview LEDsPower Supply Status Through System Management Auto-Ranging Power Supplies Lanview Diagnostic LEDs Secure Networks Policy SupportStandards Compatibility Standalone or Rack Mountable Chassis Lanview Diagnostic LEDs Introduction Installation Requirements and Guidelines Site Guidelines Configuration Guidelines Power Supply LEDsPower Supply PS LED Status Definitions Lanview LEDs NAC Controller PEP Network Requirements Fan LEDFan LED States and Definitions LED Color Status Link Aggregation 10BASE-T Network100BASE-TX Network 1000BASE-T Network 1000BASE-SX/LX/ELX Network Page Enterasys Matrix N1 Chassis Setup Unpacking the Enterasys Matrix N1 Chassis Setting Up the Enterasys Matrix N1 Chassis Installing the Chassis on a Flat SurfaceOrder of Installation Quantity Installing the Rubber Feet Installing the Chassis into a RackInstalling the Chassis on the Rack Shelf Installing the Chassis Directly to the Rack Attaching the Electrostatic Discharge Wrist Strap Powering Up a Enterasys Matrix N1 Chassis ESD Grounding Receptacle Connecting the 15-Amp AC Power Cords Cooling Fans NAC Controller PEP Installation Required ToolsUnpacking the NAC Controller PEP Important Notice Installing Optional Mini-GBICs Contents of Module Carton Quantity Installation Mini-GBIC with LC Connector Installing NAC Controller PEP into the Matrix N1 Chassis Removing the Mini-GBIC Installation Preparation Connecting to the Network Connecting UTP Cables to the 2S4082-25N1 Chassis slot Metal back panel FTM2 backplane connectors NAC Controller PEP card Connecting a Twisted Pair Segment to the NAC Controller PEP RJ45 connector RJ45 port connector port Group Select button RX+ TX1+ RX1 TX2+ TX3+ RX3 RX2 TX4+ RX4 Connecting Fiber-Optic Cables to Mini-GBICs 10 Cable Connection to MT-RJ Fiber-Optic Connectors 11 Cable Connection to LC Fiber-Optic Connectors Connecting to COM Port for Local Management What Is NeededConnecting to an IBM PC or Compatible Device Parameter Setting Connecting to a VT Series Terminal 12 Connecting an IBM PC or Compatible Connecting to a Modem 13 Connecting a VT Series Terminal COM Port Adapter Wiring and Signal Diagram Adapter Wiring and Signal AssignmentsRJ45 Completing the Installation VT Series Port Adapter Wiring and Signal DiagramModem Port Adapter Wiring and Signal Diagram RJ45 DB25 First-Time Log-In Using a Console Port Connection 15 Matrix DFE Startup Screen Example N7 Chassis Troubleshooting Using LanviewAbout the Management Mgmt LED Viewing the Receive and Transmit Activity Lanview LEDs for the 2S4082-25 Lanview LEDs for the 7S4280-19 Color State Recommended Action Lanview LEDsAlternating 67% on, 33% off Troubleshooting Checklist Series Configuration Guide for proper setup Troubleshooting Checklist Problem Possible Cause Recommended Action Overview of the NAC Controller PEP Shutdown Procedure OFFLINE/RESET Switch for the 2S4082-25 Recommended Shutdown Procedure Last Resort Shutdown ProcedurePage Initializing the NAC Controller NAC Controller Ports General Management Considerations Layer 3 NAC Controller Positioning Layer 2 In-Band Management Topology Layer 2 Out-Of-Band Management Topology Preparation for NAC Controller Initialization Layer 3 Out-Of-Band Management NAC Controller Initialization Procedure Choose NAC Controller Installation Type Enter the Management Vlan ID NAC Controller Initialization Procedure 12 Setup NAC Controller PEP Networking 13 Enter NetSight Server IP Address 16 Configure System Date and Time 17 Set the System Date 19 Select the UTC/Local Hardware Clock Setting 21 Enable an Snmp Daemon Setup the Vlan Configurations NAC Controller Policy ConfigurationNAC Controllers Require Separate Domains 24 Determining NAC Controller Mode of Operation Modifying NAC Controllers Preconfigured Policy 25 Import From Device Wizard 26 Import From Device Wizard 28 Services Screen Adding Assessment Classification Rules Modifying the Downstream Default Policy Page Specifications and Regulatory Compliance 7C111 Chassis Specifications and Regulatory CompliancePhysical Specifications Table A-1 Chassis Specifications Physical Environmental Requirements Power SupplyRegulatory Requirements NAC Controller Engine Interface Specifications Table A-5 NAC Controller Engine Specifications PortsExternal Power Supply Processor/Memory Table A-5 NAC Controller Engine Specifications Table A-6 COM Port Pin Assignments Signal Name Input/OutputNAC Controller Engine COM Port Pinout Assignments Environmental NAC Controller PEP 2S4082-25 Module Specifications Table A-7 Specifications for 2S4082-25Ports Processors/Memory NAC Controller PEP 7S4280-19 Specifications Table A-8 COM Port Pin Assignments Signal Name Input/OutputTable A-9 Specifications 2S4082-25 COM Port Pinout Assignments Table A-10 Mini-GBIC Input/Output Port Specifications Mini-GBIC Input/Output Specifications7S4280-19 COM Port Pinout Assignments MGBIC-LC01/MGBIC-MT01 Specifications 1000BASE-SX Gigabit Ethernet SpecificationsMGBIC-LC03 Specifications 1000BASE-SX MGBIC-LC09 Specifications 1000BASE-LX MGBIC-08 Specifications 1000BASE-ELX MGBIC-02 Specifications 1000BASE-T Table A-20 MGBIC-02 / SpecificationsRegulatory Compliance Table A-21 Compliance Standards Mode Switch Bank Settings Optional Installations Setting the Mode Switches Memory Locations and Replacement Procedures Location of Memory Modules Flash Dimm Replacement Procedure Connector armsConnector fingers Flash Dimm Installing the Dimm Figure B-4 Installing the Dimm Dram Simm Replacement Procedure Installing the Dram SimmConnector contacts Removing the Dram Simm Dram Simm Connector arms Connector contacts Dram Simm alignment notches Index Numerics Index-2