Enterasys Networks 7S4280-19-SYS, 2S4082-25-SYS Preparation, Installation

Installing NAC Controller PEP into the Matrix N1 Chassis

4-6 NAC Controller PEP Installation

Preparation

1. Removetheblankpanelcoveringtheslotinwhichthemodulewillbeinstalled.(Savethe

blankplateintheeventyouneedtoremovethemodule.)

2. Removethemodulefromtheshippingbox.(Savetheboxandpackingmaterialsintheevent

themoduleneedstobereshipped.)

3. Locatetheantistaticwriststrapshippedwiththechassis.Attachtheantistaticwriststrapto

yourwristandplugthecablefromtheantistaticwriststrapintotheESDgroundingreceptacle

attheupperrightcornerofthechassis.

4. Removethemodulefromtheplasticbag.(Savethebagintheeventthemodulemustbe

reshipped.)ObserveallprecautionstopreventdamagefromElectrostaticDischarge(ESD).

5. Examinethemodulefordamage.Ifanydamageexists,DONOTinstallthemodule.

ImmediatelycontactEnterasys Networks.Referto“GettingHelp”onpage xviii.

ToinstalltheNACControllerPEP,refertoFigure 4‐4andproceedasfollows:

1. LocatethechassiscardguidesasshowninFigure 4‐4onpage 4‐7.Makesurethemodule

lockingleversareintheopenposition(topandbottom).

2. Alignthemodulecardbetweentheupperandlowercardguidesofthedesiredslotandslide

itintothechassis,takingcarethatthemoduleslidesinstraight.SeeCautionbelow.

3. Slidethemoduleintotheslotuntilyoucanengagethetopandbottomlockinglevers.

4. RefertotheCautionnoteabove,thenrotatethetwoleversintotheclosedposition.

5. Ifthechassisinwhichthemoduleisinstalledwaspowereddownfortheinstallation,turnthe

powersupplieson.ChecktoseethatthemoduleCPULEDsettlesatsolidgreenafterafew

minutes.IftheLEDdoesnotturnsolidgreen,refertoChapter 5fortroubleshootingdetails.

Caution: To prevent damaging the backplane connectors in the following step, take care that the

module slides in straight and properly engages the backplane connectors.

Ensure that the top lever lines up with the desired slot number located on the front panel of the

chassis. Refer to Figure 4-4.

Precaución: Para evitar que se dañen los conectores del panel posterior en el siguiente paso,

intente deslizar el módulo en forma recta y verifique que se enganche correctamente en los

conectores de panel posterior.

Asegúrese de que la palanca superior esté alineada con respecto al número de ranura

correspondiente ubicado en el panel frontal del chasis. Consulte en Figure 4-4.

Caution: Due to the amount of force needed to properly seat the NAC Controller PEP connectors

into the backplane connectors, it is best to apply force to the end of the levers to insert (or eject) the

module. Otherwise, damage could result to the module and chassis.

Precaución: Para colocar los conectores del módulo en los conectores del panel posterior

correctamente es necesario hacer bastante fuerza, por ello, para insertar o quitar el módulo, se

recomienda concentrar la fuerza en el extremo de las palancas. Si no lo hace, podría dañar el

módulo y el chasis.

Caution: In step 4, do not force the locking levers to the point that they touch the face of the front

panel. Forcing the locking levers to this point could damage the module and chassis.

Precaución: En el paso 4, tenga cuidado de no llevar las palancas de cierre a un punto en donde

estén en contacto con el panel frontal. Si lo hace, podría dañar el módulo y/o el chasis.