Extron electronic RCP 2000 Resetting the Unit, Implementing a title, Implementing an effect, 3-11

Operation, cont’d

S t a r t h e r e
S O F T W I P E	S O F T W I P E	S O F T W I P E	S O F T W I P E	H A R D W I P E
LT t o R T	R T t o LT	T P t o B M	B M t o T P	LT t o R T

If you want to control the effect by hand, move the T-bar at the desired rate.

Implementing a title

H A R D W I P E R T t o LT

SC U R T V E R T I N

HC U R T

V E R T O U T

T I T L E

W I N D O W

H A R D W I P E

T P t o B M

SC U R T

V E R T O U T

P L U S

W I P E I N

H A R D W I P E

B M t o T P

HC U R T H R Z I N

P L U S

W I P E O U T

SC U R T H R Z I N

HC U R T H R Z O U T

S Q U A R E W I P E I N

SC U R T H R Z O U T

HC U R T V E R T I N

S Q U A R E

W I P E O U T

To implement a title, do the following:

1.	Press the preview input button to display the preview
	image on the preview monitor.
2.	Press the Effect button that has been selected for the title.
	(If the button is already lit, you do not need to press it.)
3.	When you want the title to begin, press the Take button.
	The portion of the program image dissolves to reveal the
	title. The Take light remains on.
4.	When you want to end the title, press the Take button
	again. The title dissolves during the time specified by the

Figure 3-8 — Available wipes

To select the duration of a wipe, do the following:

1.	Press and release the Wipe button. The Wipe button lights
	and a duration menu appears on the LCD screen, showing
	the current duration selected for the wipe.
2.	Rotate the Adjust knob next to the buttons, and select any
	wipe duration from 0.2 to 5.0 seconds as indicated on the
	LCD screen.
	H W L e f t	H W L e f t	H W L e f t	H W L e f t
	0 . 2 S e c .	0 . 3 S e c .	0 . 4 S e c .	0 . 5 S e c .

Figure 3-9 — Wipe duration

Implementing an effect

To implement an effect after it has been set up on the RCP 2000, follow these steps. (For a title effect, see Implementing a title, on the next page.)

1.	Press the preview input button to display the preview
	image on the preview monitor.
2.	Press the Effect button for the desired effect. (If the button
	is already lit, you do not need to press it.)
3.	When you want the effect to occur, press the Take button.
	The Take button lights, the effect occurs during the time
	specified by the duration, and the Take button light turns
	off.

- OR-

duration, and the Take button light turns off.

Resetting the Unit

There are three reset modes available by using the Reset button (item 5 , page 2-2) on the rear panel. The Reset switch is recessed, so use of a pointed stylus, ballpoint pen, or Extron Tweeker is suggested.

CAUTION	Review the reset modes carefully. Use of the wrong
	reset mode may result in unintended loss of flash
	memory programming, reassignment of ports, or
	unit reboot.

R E S E T Mode 1 — Pressing and holding the Reset button until the front

M O D E 1panel LCD display shows “Reset Mode 1” (3 seconds), then immediately pressing the button momentarily (for less than one second), causes all events to stop running. The LCD screen displays “Unit reset” when the Mode 1 reset is complete.

Nothing happens if the second, momentary press does not occur within one second.

R E S E T Mode 2 — Pressing and holding the Reset button until the front

M O D E 2panel LCD display shows “Reset Mode 2” (5 seconds), then immediately pressing the button momentarily (for less than one second) erases all user flash memory, resets ports to default conditions, and reboots the unit. The LCD screen displays “Unit reset” when the Mode 2 reset is complete.

Nothing happens if the second, momentary press does not occur within one second.

3-10 RCP 2000 • Operation RCP 2000 • Operation 3-11