McQuay Micro Tech Open Protocol Driver Manual

Page 33 of 35

Appendix B. Error Messages

Those messages marked with an * are only printed once even if they occur repeatedly.

Error Message

Action

McQuay:#1 FYI. The MapDesc

The length of the Map Descriptor used to expose driver statistics is

too short. Set the length to at least 1000. You can ignore this

called <%s> is too short

message – the driver will abandon excess statistics.

 

McQuay:#2 FYI. You could

You can safely ignore this message. It is a prompt. Refer to

have used a MapDesc called

Appendix A.8.

<%s> to expose diagnostic info.

McQuay:#3 FYI. Normally

This is a reminder that a password is expected when a node is

defined. Refer to sections 4.3 or 5.2. Even though password

passwords are defined for each

node.

checking is not enforced when the driver is configured as a Server,

the driver expects one to be defined for every node.

 

McQuay:#4 Err. Node list if full.

A maximum of 100 McQuay device nodes can be configured per

Max=%d

FieldServer. If the limit is reached, call support.

 

A node has been provided with two passwords. This is either a

 

configuration error or two nodes with the same address are

McQuay:#5 Err. Node=%d has

connected to different ports. The driver can only store one password

more than one password.

per node address and cannot use the port number to differentiate

 

them. Re-program the McQuay devices to have the same passwords

 

if they have the same addresses.

*McQuay:#9 FYI. Device

Device Scaling is being applied and the driver doesn’t know how to

scale a variable. Please submit your configuration file with your

scaling method unknown.

request for support.

 

McQuay:#10 Err. Node=%s.

The driver doesn’t recognize the equipment type specified using the

PLC_Type parameter in the configuration file. Refer to Appendix A.3

Equip. type not recognized.

for a list of valid equipment types.10

McQuay:#11 Err. Node=%s.

Refer to Sections 4.3, 5.2. and Appendix A.310

Equip. Type not specified.

 

McQuay:#13 Err.

Refer to Appendix A.2 for a list of valid field names. Refer also to

MapDesc=%s. Field Name

Sections 4.4 or 5.3.

unknown.

 

McQuay:#14 Err.

Corrective action is required. When writing to a McQuay device using

MapDesc=%s. Max Len=1 for

direct addressing the length may only be 110

Writes with direct addr.

 

McQuay:#15 Err.

Neither a field name nor an address was specified. The driver does

MapDesc=%s. Field

not know what location to read. Specify a field name from Appendix

Name/Address Required.

A.2.10

McQuay:#16 Err.

Each Map Descriptor must be connected to a node. This is done by

MapDesc=%s. No Node.

specifying a node name. 10

McQuay:#17 Err.

The offset added to the length of the Map Descriptor extends beyond

MapDesc=%s. Md too short.

the Data Array. Increase the Data Array length. 10

McQuay:#18 Err.

When using ‘everything’ as a field name the Map Descriptor function

MapDesc=%s. Cannot write

must be Rdbc or Rdb as this is a read only function.10

'Everything'.

 

McQuay:#19 do diagnostic 3

Call FieldServer Technical Support. A developer diagnostic has been

McQuay:#20 do diagnostic 1

called and should not have been.

McQuay:#21 do diagnostic 2

 

10Correct the configuration by editing the CSV file and downloading it to the FieldServer, then reset the FieldServer for the changes to take effect.

FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web: www.fieldServer.com Tel: (408) 262 2299 Fax: (408) 262 2269 Toll Free: (888) 509 1970 email: support@fieldServer.com

Page 33
Image 33
FieldServer FS-8700-80 instruction manual