Connecting the Fiber Optic Cable | Foxconn 7870 specification

2.2 Connecting the Fiber Optic Cable

2.2Connecting the Fiber Optic Cable

Before connecting the cable:

1.The fiber optic cable must be either fusion spliced or connected via FC/APC connectors.

2.Wipe the connector with a lint-free cotton cloth.

3.Note the polarity key of the optical connector before inserting.

To connect the cable:

1.Line Up the Polarity Key.

2.Insert the connector

3.Tighten the connector

Caution Do not apply any glue, silicon adhesive, or any other material to the fiber optic connector!

7870 Interfacility Link Installation and User’s Guide	page 9
Foxcom proprietary information

Image 17

Foxconn 7870 manual Connecting the Fiber Optic Cable

Contents

Copyright Interfacility Link Installation and User’s Guide Mailsales@foxcom.com Table of Contents Figures General Warranty Warranty and Repair PolicySpecific Product Warranty Instructions Important Information Limitations of Liabilities Returns Personal Safety PrecautionsEquipment Safety Reporting Defects Important Information Introduction to the 7870 Interfacility Link Options Product Drawings Panel Descriptions Block Diagrams Option Label Options 7870T Transmitter Front and Rear Panel Product Drawings LED Name LED Function Opt Panel DescriptionsLED Name LED Function Laser 7870Transmitter Block Diagram Block Diagrams Block Diagrams Typical Application of a 7870 Interfacility Link Installation Setting up the Transmitter Connecting the Fiber Optic Cable Setting Up the Receiver Powering the IFL 7180M Chassis Rear View 1 7180M Chassis Jumper Installation Tx and Rx only Connecting the Back Panel Jumpers Jumper Installation 2040 Switch in slots 2 Aligning the Fiber Optic Link Fiber Optic Alignment Setup Document no -005-35-C5 RF Specifications Product Specifications Physical Specifications Optical Specifications Unit dimensions Model Dimensions 7870 Interfacility Link Pinouts 7870R Receiver Pinout 7180M Chassis Pinouts 7870 the J11 connector is inoperative Pin No Function Name Slot No 7180M Alarm Connector J12 Pinouts 3 7180M and Redundancy Switching 2 7180M Monitor Connector Pinout J13 Pin # Function Name Problem Possible Cause Troubleshooting May still function without LED Description Manufacturer Appendix 1 Cleaning Fiber Optic Connections Wiping the connector with a Kim wiper Appendix 1.1 Cleaning Procedures for FC/APC Connectors Appendix 1.2.2 Compressed Air Method Appendix 1.2 Cleaning Procedure for FC/APC Bulkhead PortsAppendix 1.2.1 Swab Method Appendix 1.2 Cleaning Procedure for FC/APC Bulkhead Ports Appendix 2 Installing a Standalone Unit Document no -005-35-C5 Appendix 3 The 2380 Relay Adapter Appendix 2380 Dimensions and Front Panel Label Appendix 3.1.2 Mounting the the 2380 Relay Adapter Appendix 3.1 Installing the 2380 Relay AdapterAppendix 3.1.1 Parts Required for Installing Mounting the Screws 2380 Dimensions Appendix 3.2 2380 Dimensions and Front Panel Label Slot Number Appendix Adapter PinoutsPin Number Function 2380 Pin Number Pin # Function Name Slot No Appendix 4 Pinout Charts and Diagrams Standard 7180M and 7180M with 2380 Relay Adapter Pinout 7180M and 2040 RF Switch Pinout Pinout of 7180M Jumper with 2040 RF Switch in slots 2 Pinout of 7180M jumper with 2040 RF switch in slot Pinout of 7180M jumper with 2040 RF switch in slot Page Document no -005-35-C5