Connecting the Back Panel Jumpers | Foxconn 7870 instruction

2.5 Connecting the Back Panel Jumpers

2.5Connecting the Back Panel Jumpers

On the rear panel of the 7180M Back Panel are product selectors (JP1 to JP4). The 3 pin selectors (male) are the connecting point between the slots and the back panel. One pin is for the transmitter/receiver (Tx/Rx), one is for the optional 2040 1:1 Redundant Switch, and one is for the 7180M. A 2 pin jumper (female) is placed on the relevant pins to complete the connection between the 7180M and the units. For example, if a 2040 Switch is being used, the jumper is placed on the Switch-7180M pins.

To connect the jumpers:

1.Each jumper has two sets of pins, upper and lower. The upper pins are labeled SW (Switch) and the lower pins Tx/Rx.

2.If the 7180M has Tx or Rx units only, place all jumpers on the lower two pins.

Figure 8 Jumper Installation: Tx and Rx only

3.If the 2040 Switch is installed in Slot 2, place the JP1 and JP2 jumpers on the higher two pins and the JP3 and JP4 jumpers on the lower two pins.

Figure 9 Jumper Installation: 2040 Switch in slot 2

7870 Interfacility Link Installation and User’s Guide	page 13
Foxcom proprietary information

Image 21

Foxconn 7870 manual Connecting the Back Panel Jumpers, Jumper Installation Tx and Rx only

Contents

Copyright Interfacility Link Installation and User’s Guide Mailsales@foxcom.com Table of Contents Figures General Warranty Warranty and Repair PolicySpecific Product Warranty Instructions Important Information Limitations of Liabilities Returns Personal Safety PrecautionsEquipment Safety Reporting Defects Important Information Introduction to the 7870 Interfacility Link Options Product Drawings Panel Descriptions Block Diagrams Option Label Options 7870T Transmitter Front and Rear Panel Product Drawings Panel Descriptions LED Name LED Function LaserLED Name LED Function Opt 7870Transmitter Block Diagram Block Diagrams Block Diagrams Typical Application of a 7870 Interfacility Link Installation Setting up the Transmitter Connecting the Fiber Optic Cable Setting Up the Receiver Powering the IFL 7180M Chassis Rear View 1 7180M Chassis Jumper Installation Tx and Rx only Connecting the Back Panel Jumpers Jumper Installation 2040 Switch in slots 2 Aligning the Fiber Optic Link Fiber Optic Alignment Setup Document no -005-35-C5 RF Specifications Product Specifications Physical Specifications Optical Specifications Unit dimensions Model Dimensions 7870 Interfacility Link Pinouts 7870R Receiver Pinout 7180M Chassis Pinouts 7870 the J11 connector is inoperative Pin No Function Name Slot No 7180M Alarm Connector J12 Pinouts 3 7180M and Redundancy Switching 2 7180M Monitor Connector Pinout J13 Pin # Function Name Problem Possible Cause Troubleshooting May still function without LED Description Manufacturer Appendix 1 Cleaning Fiber Optic Connections Wiping the connector with a Kim wiper Appendix 1.1 Cleaning Procedures for FC/APC Connectors Appendix 1.2 Cleaning Procedure for FC/APC Bulkhead Ports Appendix 1.2.1 Swab MethodAppendix 1.2.2 Compressed Air Method Appendix 1.2 Cleaning Procedure for FC/APC Bulkhead Ports Appendix 2 Installing a Standalone Unit Document no -005-35-C5 Appendix 3 The 2380 Relay Adapter Appendix 2380 Dimensions and Front Panel Label Appendix 3.1 Installing the 2380 Relay Adapter Appendix 3.1.1 Parts Required for InstallingAppendix 3.1.2 Mounting the the 2380 Relay Adapter Mounting the Screws 2380 Dimensions Appendix 3.2 2380 Dimensions and Front Panel Label Appendix Adapter Pinouts Pin Number FunctionSlot Number 2380 Pin Number Pin # Function Name Slot No Appendix 4 Pinout Charts and Diagrams Standard 7180M and 7180M with 2380 Relay Adapter Pinout 7180M and 2040 RF Switch Pinout Pinout of 7180M Jumper with 2040 RF Switch in slots 2 Pinout of 7180M jumper with 2040 RF switch in slot Pinout of 7180M jumper with 2040 RF switch in slot Page Document no -005-35-C5