Appendix 2 Installing a Standalone Unit | Foxconn 7870 guide

Appendix 2 Installing a Standalone Unit

To install the 7870T-STD or 7870R--STD Standalone:

1.Place the 7870 unit on the standalone flange, matching the holes.

2.Using four screws (#4 or #6) secure the unit and the flange to the wall.

3.Apply AC power to the standalone power supply unit.

4.Connect the 7870 unit to the power supply. The Laser LED should be lit.

All remaining steps are the same as in the product manual. See sections 2.1 Setting up the Transmitter on page8 and 2.3 Setting Up the Receiver on page10.

7870 Interfacility Link Installation and User’s Guide	page 31
Foxcom proprietary information

Image 39

Foxconn 7870 manual Appendix 2 Installing a Standalone Unit

Contents

Copyright Interfacility Link Installation and User’s Guide Mailsales@foxcom.com Table of Contents Figures Important Information Warranty and Repair PolicyGeneral Warranty Specific Product Warranty Instructions Limitations of Liabilities Returns Reporting Defects PrecautionsPersonal Safety Equipment Safety Important Information Introduction to the 7870 Interfacility Link Options Product Drawings Panel Descriptions Block Diagrams Option Label Options 7870T Transmitter Front and Rear Panel Product Drawings Panel Descriptions LED Name LED Function LaserLED Name LED Function Opt 7870Transmitter Block Diagram Block Diagrams Block Diagrams Typical Application of a 7870 Interfacility Link Installation Setting up the Transmitter Connecting the Fiber Optic Cable Setting Up the Receiver Powering the IFL 7180M Chassis Rear View 1 7180M Chassis Jumper Installation Tx and Rx only Connecting the Back Panel Jumpers Jumper Installation 2040 Switch in slots 2 Aligning the Fiber Optic Link Fiber Optic Alignment Setup Document no -005-35-C5 RF Specifications Product Specifications Physical Specifications Optical Specifications Unit dimensions Model Dimensions 7870 Interfacility Link Pinouts 7870R Receiver Pinout 7180M Chassis Pinouts 7870 the J11 connector is inoperative Pin No Function Name Slot No 7180M Alarm Connector J12 Pinouts 3 7180M and Redundancy Switching 2 7180M Monitor Connector Pinout J13 Pin # Function Name Problem Possible Cause Troubleshooting May still function without LED Description Manufacturer Appendix 1 Cleaning Fiber Optic Connections Wiping the connector with a Kim wiper Appendix 1.1 Cleaning Procedures for FC/APC Connectors Appendix 1.2 Cleaning Procedure for FC/APC Bulkhead Ports Appendix 1.2.1 Swab MethodAppendix 1.2.2 Compressed Air Method Appendix 1.2 Cleaning Procedure for FC/APC Bulkhead Ports Appendix 2 Installing a Standalone Unit Document no -005-35-C5 Appendix 3 The 2380 Relay Adapter Appendix 2380 Dimensions and Front Panel Label Appendix 3.1 Installing the 2380 Relay Adapter Appendix 3.1.1 Parts Required for InstallingAppendix 3.1.2 Mounting the the 2380 Relay Adapter Mounting the Screws 2380 Dimensions Appendix 3.2 2380 Dimensions and Front Panel Label Appendix Adapter Pinouts Pin Number FunctionSlot Number 2380 Pin Number Pin # Function Name Slot No Appendix 4 Pinout Charts and Diagrams Standard 7180M and 7180M with 2380 Relay Adapter Pinout 7180M and 2040 RF Switch Pinout Pinout of 7180M Jumper with 2040 RF Switch in slots 2 Pinout of 7180M jumper with 2040 RF switch in slot Pinout of 7180M jumper with 2040 RF switch in slot Page Document no -005-35-C5