Manuals / Frymaster / Kitchen Appliance / Fryer

Frymaster FMCF mode. cont, CM III.5 displays, as it comes out of, melt cycle, Heating mode

Models: FMCF

1 50

Download 50 pages 20.61 Kb

Page 43

mode. (cont.)

CF SERIES GAS FRYERS

CHAPTER 6: OPERATOR TROUBLESHOOTING

6.2Troubleshooting Fryers with Solid State (Analog), Digital, or CM III.5 Controllers (cont.)

	PROBLEM	PROBABLE CAUSES	CORRECTIVE ACTION
			B. If available, substitute controller
	CM III.5 will not go		known to be good for suspect
	CM III.5 will not go		controller (see Section 6.6). If
	into programming	B. Failed controller.	controller (see Section 6.6). If
	into programming	B. Failed controller.	fryer operates normally, order
	mode. (cont.)		fryer operates normally, order
	mode. (cont.)		replacement controller from
			replacement controller from
			FASC.
		A. Setpoint incorrect.	A. Verify that setpoint has been
	CM III.5 displays	A. Setpoint incorrect.	properly entered.
			properly entered.
			B. Disconnect unit from electrical
	as it comes out of		B. Disconnect unit from electrical
	as it comes out of	B. Temporary controller malfunction	power, wait at least one minute,
	melt cycle	caused by voltage surge.	and reconnect unit to the power
		caused by voltage surge.	and reconnect unit to the power
	OR		supply.
	OR		C. If available, substitute controller
			C. If available, substitute controller
	Heating mode		known to be good for suspect
	Heating mode		controller (see Section 6.6). If
	indicator does not	C. Failed controller.	controller (see Section 6.6). If
	indicator does not	C. Failed controller.	fryer operates normally, order
	come on at all.		fryer operates normally, order
	come on at all.		replacement controller from
			replacement controller from
			FASC.
			A. Refer to Burner does not light
		A. Burner is not lit.	problem on the following page in
	Heating mode		Sec. 6.3.
	Heating mode		B. If available, substitute controller
	indicator is on but		B. If available, substitute controller
	indicator is on but		known to be good for suspect
	fryer is not heating		known to be good for suspect
	fryer is not heating		controller (see Section 6.6). If
	properly.	B. Failed controller.	controller (see Section 6.6). If
	properly.	B. Failed controller.	fryer operates normally, order
			fryer operates normally, order
			replacement controller from
			FASC.

6-3

Image 43

Frymaster FMCF mode. cont, CM III.5 displays, as it comes out of, melt cycle, Heating mode, indicator does not, properly

Contents

June Installation andCF Series Gas FryersREQUIREMENTS in Chapter 2 of this manual for specifics Page CHAPTER 6 Operator Troubleshooting TABLE OF CONTENTSCHAPTER 2 Installation Instructions CHAPTER 5 Preventive MaintenanceCF SERIES GAS FRYERS CHAPTER 1 INTRODUCTION 1.2 Parts Ordering and Service Information1.1 Applicability and Validity CF SERIES GAS FRYERS CHAPTER 1 INTRODUCTION 1.3 Safety Information1.4 European Community CE Specific Information CE Standard for Incoming Gas Pressures1.5 Equipment Description Warranty on your equipment 1.6 Installation, Operating, and Service Personnel1.7 Definitions 1.8 Shipping Damage Claim Procedure 2.1 General Installation Requirements CF SERIES GAS FRYERS CHAPTER 2 INSTALLATION INSTRUCTIONSThe fryers must be installed with a 6 150 mm clearance at both sides and back when installed adjacent to combustible construction no clearance is required when installed adjacent to noncombustible construction. A minimum of 24 600 mm clearance should be provided at the front of the fryer The type of gas for which the fryer is equipped is stamped on the data plate attached to the inside of the fryer door. Connect a fryer stamped NAT only to natural gas, those stamped PRO only to propane gas, and those stamped MFG only to manufactured gas 2.3 Pre-Connection Preparations 2.2 Caster/Leg Installation4. Test the fryer electrical system 2.4 Connection to Gas Line CE Standard 2.5 Converting to Another Gas Type CE Gas Conversion Instructions Non-CE Gas Conversion InstructionsCE Only 2-10Non-CE Only CE Gas Valve 3.1 Start-Up ProcedureCF SERIES GAS FRYERS CHAPTER 3 OPERATING INSTRUCTIONS Non-CE Gas Valveleast five minutes before attempting to re-light ACCESSING THE PILOTCF SERIES GAS FRYERS CHAPTER 3 OPERATING INSTRUCTIONS LIGHTING THE PILOT ON NON-CE FRYERS1. Ensure power to the unit is OFF, and then press the OFF red button. Wait 5 minutes branded locations 3.2 Boiling-Out the Frypot5. For units equipped with a Computer Magic III.5 Computer 3.4 Controller Operation and Programming 3.3 Shutting the Fryer Down4.1 Draining and Manual Filtering CF SERIES GAS FRYERS CHAPTER 4 FILTRATION INSTRUCTIONSIf you are using a Frymaster filter cone holder, be sure that the cone holder rests securely on the metal container 4.2 Filter Magic II Filtration System Operation 4.2 Filter Magic II Filtration System Operation cont 7. Replace the crumb tray in the filter pan 4.2 Filter Magic II Filtration System Operation cont1. To filter the oil, bring oil to operating temperature and turn the fryer power OFF. Then open the drain valve on the fryer you have selected to be filtered. If necessary, use the Fryer’s Friend steel rod to clear the drain from inside the frypot as necessary of the fryer and may cause injury CF SERIES GAS FRYERS CHAPTER 4 FILTRATION INSTRUCTIONS DANGERDrain handle in the closed position Clean Fryer Cabinet Inside and Out CF SERIES GAS FRYERS CHAPTER 5 PREVENTATIVE MAINTENANCE5.1 Fryer Preventive Maintenance Checks and Services Inspect Fryer and Accessories for DamageClean Float Switch and Shaft Check Recovery TimeDrain and Clean Frypot Clean Detachable Parts and Accessories Check Thermostat Controller Thermostat Calibration Clean Gas Valve Vent TubeCheck Computer Magic III Set Point Accuracy Check Burner Manifold Pressure Fryer 5.3 Annual/Periodic System InspectionBuilt-In Filtration System 6.1 Introduction CF SERIES GAS FRYERS CHAPTER 6 OPERATOR TROUBLESHOOTINGSolid state analog controller power andBurner will not lightCM III.5 displays indicator does notindicator is on but mode. contBurner does not 6.3 Troubleshooting Fryers with Thermostat Controls6.4 Troubleshooting the Built-In Filtration System frying temperaturetransfer takes place 6.4 Troubleshooting the Built-In Filtration System contfiltering. cont Pump starts, but nospraying properly Power Shower is notor the transfer is very slow. contand burner is 6.5 Troubleshooting Abnormal Burner OperationFlame is visible above flue opening6.6 Replacing the Controller or Controller Wiring Harness THIS PAGE INTENTIONALLY LEFT BLANK Price $12.00 SERVICE HOTLINEShipping Address 8700 Line Avenue, Shreveport, Louisiana FAX Parts 1-318-219-7140 FAX Tech Support