Manuals / Brands / Computer Equipment / Scanner / Fujitsu / Computer Equipment / Scanner

Fujitsu fi-5120C, fi-5220C Chapter2 INSTALLATION OF THE SCANNER, 2.1 Installing the Scanner

1 28

Download 28 pages, 1.38 Mb

Chapter2 INSTALLATION OF THE SCANNER

2.1 Installing the Scanner

1. Place the scanner at its installation site.

For details on the scanner's dimensions and required installation space, refer to "fi-5120C/fi- 5220C Operator’s Guide" "7.2 Installation Speci- fications" in the Setup CD-ROM.

For fi-5120C, go to Step 3.

2. Unlock the Shipping lock.

The carrier unit inside the scanner is fixed in place by the shipping lock to prevent the scanner from becoming damaged during transportation from the factory.

After transporting and placing the scanner, tilt the scanner (approx. 30 degrees) and release the Shipping lock on the bottom of the scanner.

ADF paper chute

Tab

Side guide

4. Connect the AC adapter.

ATTENTION

Use only the AC adapter provided by the manufacturer.

Approx.30 degrees

Lock Release

3. Attach the ADF paper chute.

Hold the ADF paper chute and insert its tabs into the corresponding slots in the scanner as shown in the next figure below.

The Side guides of the ADF paper chute have to face up.

1) Connect the AC cable to the AC adapter.

2)Connect the AC adapter connector to the scan- ner’s DC inlet.

3) Plug the AC cable into the outlet.

	The Function Number Display and the LED
HINT	may flash for an instant when plugging the
	AC cable into the outlet.

fi-5120C/fi-5220C Image Scanner Getting Started		3

Contents

fi-5120C/fi-5220CImageScanner Getting Started Page CONTENTS ■ Regulatory Information ■ Note, Liability ■ Safety Precautions Chapter1 INTRODUCTION ■Regulatory Information ■Note, Liability Manufacturer PFU LIMITED International Sales Dept., Imaging Business Division, Products Group Solid Square East Tower, 580 Horikawa-cho ■Safety Precautions Do not install the scanner on unstable surfaces Do not block the ventilation ports Before moving the scanner, disconnect the power plug from the power outlet Protect the scanner from static electricity Do not place heavy objects or climb on top of the scanner Chapter1 PREPARING THE SCANNER 1.1Checking the Contents of the Scanner Package 1.2Names and Functions of Parts 1.3 Operator Panel Chapter2 INSTALLATION OF THE SCANNER 2.1 Installing the Scanner 2.2Connecting the Scanner to Your PC 2.3Installing the Scanner Application For FUJITSU TWAIN32 Scanner Driver 4.Insert the Setup CD-ROMinto the CD drive ⇒<SETUP DISK START UP SCREEN> appears 5. Click [INSTALL PRODUCTS] 6. Click [TWAIN Driver] on the window below 9.Install the application following the instructions on the window ■Installing ScandAll 5.Install the application following the instructions on the window 6.When the [InstallShield Wizard Complete] win- dow appears, click [Finish] 1.Insert the Setup CD-ROMinto the CD drive 2.Click [INSTALL PRODUCTS] For FUJITSU ISIS Scanner Driver 4.Insert the "Setup CD-ROM"into the CD drive CD drive until your PC has completely restarted 6. Click [ISIS Driver] on the window below ■Installing QuickScan Pro™ plays troubleshooting information on screen if 2. Click [INSTALL PRODUCTS] 3.Click [QuickScan PRO (Trial)] on the window below 5.Enter the required information, then click [Next >] button 4.Continue to install the application following the instructions on the window 6.Install the application following the instructions on the window Error Recovery Guide (Trial) 5. Follow the instructions to install the software ■Uninstalling Supplied Programs Follow the procedure below to uninstall supplied pro- grams 1. Start up your PC 2.Exit all currently running programs 5.Click the [Change/Remove] or [Remove] but- ton 6.When the confirmation dialogbox appears, Click the [OK] or [Yes] button ⇒This executes the uninstallation Appendix1 TROUBLESHOOTING Appendix1 AP-1 AP-2 AP-3 Appendix2 DAILY CARE Appendix3 REPLACING CONSUMABLES Appendix3 AP-5 P3PC-1312-02EN