Manuals / Brands / Computer Equipment / Scanner / Fujitsu / Computer Equipment / Scanner

Fujitsu S300M 3.4 Scanning Business Cards using Cardiris, ⇒Scanning is started, clicking the ScanSnap Manager icon, ⇒When scanning is complete, Cardiris window appears

1 38

Download 38 pages, 1.07 Mb

3.4 Scanning Business Cards using Cardiris

1.Select "Cardiris" in the "Select a Profile" window which pops up whenclicking the ScanSnap Manager icon .

In Quick Menu Mode, ScanSnap cannot interact with Cardiris.

ATTENTION

2.Load the document onto the ScanSnap and press the [SCAN] button.

-Load the business cards face down.

-When scanning more than one business card, set them together.

-Adjust the side guides so that they are touching the edges of the business card. When moving the side guides, hold the tag of the side guide.

Paper chute

Business card

Side guide [SCAN] button

ATTENTION

•Do not connect or disconnect other USB devices during the scanning operation.

•Do not close the paper chute on the ScanSnap during the scanning operation.

•Do not switch the user to log in during the scanning operation.

⇒Scanning is started.

⇒When scanning is complete, Cardiris window appears.

ScanSnap S300M Getting Started 26

Contents

Chapter 2 Connecting the ScanSnap Chapter 3 How to Use the ScanSnap Chapter 4 Troubleshooting Introduction Manufacturer Trademarks How Trademarks and Product Names Are Indicated In This Manual ScanSnap and the Manuals Regulatory Information Canadian DOC Regulations Bescheinigung des Herstellers / Importeurs International ENERGY STAR® Program Use in High-SafetyApplications Conventions Symbols Used in This Manual Screen Examples in This Manual About Maintenance Safety Precautions Do not use the scanner while driving a car for safety. Accidents can happen The following describes important cautions Page Chapter 1 Preparation 1.1 Checking the Contents of the Package 1.2 Names and Functions of Parts ■Front View ■Rear View Chapter 2 Connecting the ScanSnap 2.1 Installing the Supplied Software ■Installing Cardiris ■Installing ScanSnap Manager 4.After the installation is complete, eject the CD-ROMfrom the CD-ROMdrive ⇒The ScanSnap Manager icon appears on the Dock menu ScanSnap S300M Operator’s Guide 2.2 Connecting the ScanSnap ■Connecting the cable • When using the USB bus power cable, your computer must have two USB ports; one for power feeding, the other for USB cable connection •When connecting with the Power cable: Use the power cable and USB cable 1.Connect the Power cable •When connecting with the USB bus power cable: Use the USB bus power cableand USB cable 1.Connect the USB bus power cable ■Turning the ScanSnap ON 3.The connection of the ScanSnap is complete Chapter 3 How to Use the ScanSnap 3.1 Scanning Documents 3.2 About the Scanning Settings 3.3 Scanning Office Documents 3.Press the [SCAN] button ⇒Scanning is started ⇒The ScanSnap Quick Menu appears after scanning The Operation Mode can be switched by clicking and holding the ScanSnap Manager icon on the Dock menu and then marking [Use Quick Menu] 3.4 Scanning Business Cards using Cardiris 3.Check the image data of the scanned business cards in the Cardiris window The images of each business card are displayed on the right A list of already scanned business cards is displayed on the left Under the image, the recognized characters are displayed 4.Should there be any recognition errors, correct the data manually 6.On the "Format:" pop-upmenu, select "Address Book 7.Click the [OK] button 8.Click the [Send] button or select [Process] - [Send] on the menu bar 9.On the menu bar, select [Cardiris] - [Quit Cardiris] to quit Cardiris Chapter 4 Troubleshooting 4.1 Troubleshooting Checklist refer to "Appendix A Uninstalling ScanSnap" in "ScanSnap S300M Operator’s Guide Page 4.2 Clearing Paper Jams Chapter 5 Daily Care 5.1Cleaning Materials 5.2 Cleaning the ScanSnap Exterior 5.3 Cleaning Inside of the ScanSnap Chapter 6 Consumables Use only the consumables specified by PFU LIMITED 9.2 Replacing the Pad ASSY 9.3 Replacing the Pick Roller