Manuals / Furuno / Marine Equipment / Marine Instruments

Furuno NAVpilot-500 manual Power Supply, Environmental Conditions, Color

Models: NAVpilot-500

1 73

Page 72

3.4 I/O ControlRS-232C (NMEA)

5	POWER SUPPLY
3.1	Processor Unit	12-24 VDC: 3-2 A (Control Unit: 6 sets)
6	ENVIRONMENTAL CONDITIONS
4.1	Ambient Temperature	-10°C to +55°C
4.2	Relative Humidity	95% at 40°C

6.3Waterproof

Processor unit:	IPX2
Control unit/ Remote controller/ Rudder reference unit: IPX5
6.4 Vibration	IEC 60945

7	COLOR
5.1	Processor Unit	N3.0
5.2	Control Unit	N3.0
5.3	Remote Controller	N3.0 (FAP-5552/6232), N1.5 (FAP-6212/6222)
5.4	Rudder Reference Unit	N1.0
5.5	Junction Box	N3.0

SP - 2

E7250S01A

Page 72

Image 72

Furuno NAVpilot-500 manual Power Supply, Environmental Conditions, Color

Contents

Autopilot Safety Instructions Table of Contents Alarms IiiFeatures ForewordWord to the Owner of the NAVpilot-500 System Configuration System configuration of NAVpilot-500This page is intentionally left blank Principle of the Autopilot Principle of AutopilotPrinciple of Operation Basic Operation Operating ControlsControl unit, front view Turning the power off Turning On/OffStartup sequence Adjusting Brilliance and Contrast DisplaysContrast, brilliance window DisplaysScreen setup menu Selecting the data shown on Normal and Data DisplaysSelecting data for Normal Display 2 screen Normal DisplayData available for display in Screen 2 Upper and Lower Displayed dataSelecting the display layout for Data Display Data DisplaysScreen 3 pattern options window Selecting data for Data DisplaySelecting the display on Graphic Display Graphic options windowGraphic displays Selecting data for analog indicator Display setup menuNormal Display 1 Analog indicator bar options window Rudder AngleThis page is intentionally left blank Stby Mode Stby mode displaySteering Modes Auto Mode Using the Auto modeAuto mode display Advanced Auto mode Advanced Auto mode displayEnabling the Advanced Auto mode Advanced auto options windowTurn mode For Auto mode Turn setting windowTurn NAV Mode Starting the NAV modeNAV mode display Selecting sailing method of NAV mode Nav mode options windowNAV mode, Course and XTE Switching waypoint Waypoint switching options windowNAV mode menu Fishing mode options window OFFOrbit mode Do not use the Orbit mode in rough seaNavigating to TLL point Fishing mode Fishing mode windowClover Leaf OrbitRemote Mode Dial type remote controller FAP-5551Turning power off dial type Rotating dialTurning power on, button and lever type remote controllers NFU No Follow-Up mode displayOperating remote controller ex. button and lever types Turning power off, button and lever type remote controllersSelecting course after the Remote mode is off Stby mode menuSystem setup menu Course after remote controller is turned off Cse course after remote options windowDodge Mode Dodging in Stby modeDodge mode display Dodging in Auto or NAV mode Stby Mode Menu Offsetting dataMenu Operation Data calibration menuOffsetting the heading data Ship’s speed, temperature, depth calibrationSelecting the selecting method of magnetic variation Magnetic variation options windowSetting parameters Parameter setup menuSelecting the method of entering the parameter Sea state options windowMANUAL-CALM Deviation level options windowSetting parameters manually Example of Manual parameterTrack line and weather setting value Rudder angle and rudder gain settingWeather Rudder GainGeneral guidelines for setting rudder gain General guidelines for setting counter rudder gainCounter Rudder Adjusting the sensitivity in monitoring the boat’s trim Auto trim options windowWhen towing the net Auto net towing options windowSetting the units of measurements Speed unit options window, for exampleDDMM.MM’ Setting other menu items Activating key beepKey beep options window Setting the panel dimmer Locking the control unitLock options window Selecting languageSimulation mode options window Running simulation programAlarms Alarm MenuAlarm menu Selecting the alarm buzzer Audio alarm options windowAlarm interval options window Selecting the beep patternSetting the watch alarm Setting the heading deviation alarmSetting the cross-track error limit Watch alarm options windowSetting the speed alarm How to use XTE alarm Into modeApplication of XTE alarm Speed alarm options windowSetting the depth alarm Depth alarm options windowSetting the temperature alarm Setting the trip distance alarmTemp alarm options window Log trip options windowAlarm Information Clearing the trip distanceLog trip clear options window Alarm messages Alarm messages, their meanings and prioritiesMaintenance & Troubleshooting Preventive MaintenanceMaintenance program Check point RemedyReplacement of Fuse DiagnosticsParts Name Type Code No Remarks Test options windowProcessor Unit Test Controller Unit TestHeading Sensor Test Keyboard Test Screen TestRudder Setup and Auto Test Rudder testClearing Memories System DataSystem data screen Memory clear options windowError Messages Error messagesError message Meaning Remedy Error messages con’t Menu Tree MN-1Stby mode menu MN-2Auto mode menu MN-3NAVpilot-500 Control UnitProcessor Unit InterfacePower Supply Environmental ConditionsColor Index IN-1

POWER SUPPLY

ENVIRONMENTAL CONDITIONS

COLOR