About the control and settings.

ge.com

Auto Bev

Indicator Light

Control Settings

Safety Instructions

The temperature range of the beverage center/ wine chiller is intended for 40°F (4,4°C) to 60°F (15,6°C). The display shows the average temperature of the appliance. It is normal for the actual temperature to vary slightly during operation.

Auto Temperature Setting

When the appliance is plugged in or the “+” pad is pressed, the appliance runs on the “Auto Bev” setting of 44°F (6,7°C) and the “Auto Bev” indicator light in the upper left corner stays lit.

NOTE: Display will flash when the “+” pad is pressed.

Normal Temperature Setting

The temperature of the beverage center can be set anywhere between 39°F (3,9°C) to 61°F (16,1°C) by the “+” and “–”pads.

Press and hold the SET pad. You will hear a series of 2 beeps.

After the second beep, press the “+” and “–”pads to increase or decrease the desired

temperature in increments of one degree. During this time the display will flash.

Press SET to confirm your choice. The display will stop flashing. If no confirmation is made in ten seconds, the unit will automatically accept your change.

NOTE: When you change the temperature setting, there may be a 5-minute delay until the compressor starts to run.

Fahrenheit and Celsius

The temperature display can be changed between Fahrenheit and Celsius by pressing and holding the “+” pad for approximately 5 seconds.

Indicator Light

The indicator is lit when the compressor is running to cool your unit. It will not be lit when the compressor is idle.

Interior Light

To switch the interior light on/off, simply press the pad.

Instructions

Installation

Instructions

Operating

Care and

When the Beverage Center/Wine Chiller is Plugged In

After plugging in the beverage center/wine chiller and setting the desired temperature, allow the beverage center/wine chiller to reach the set temperature before loading your wine. The temperature may take up to 12 hours to completely stabilize.

After loading the wine or beverages, you may notice the actual temperature rise. This is normal. The actual temperature will continue to change as the wine and beverages are cooled to the set temperature. The temperature may take up to 12 hours to completely stabilize.

A guide with wine serving temperature suggestions is located on the inside right portion of the unit.

It gives recommended temperatures for different wines, as well as instructions on adjusting the temperature of the beverage center/wine chiller.

NOTE: The exterior of the cabinet may get warm.

This is normal.

Interior Light

You can turn the light ON or OFF by pushing the

 

light switch located on the right side of the control

 

panel housing. If the interior light is left on,

 

it will raise the inside temperature.

5

Cleaning

Tips

Troubleshooting

Consumer Support

Page 4 Page 6
Page 5
Image 5
GE 197D4613P004 installation instructions About the control and settings, Instructions Installation, Care
Page 4 Page 6

197D4613P004 specifications

The GE 197D4613P004 is a highly advanced component designed for specific industrial applications, particularly in the realm of power generation and distribution systems. This electronic device is recognized for its robustness, reliability, and exceptional performance under demanding conditions.

One of the main features of the GE 197D4613P004 is its versatility, as it can be integrated into various systems, including those used in turbines, generators, and other key components in the energy sector. The device is engineered to provide accurate monitoring, control, and protection for these systems, ensuring optimal performance and safety.

The technology behind the GE 197D4613P004 includes state-of-the-art microprocessor-based control systems. This allows for real-time data processing and analysis, enhancing the capability to respond to dynamic operational conditions. The microprocessor also enables advanced communication protocols, ensuring seamless interaction with other devices and systems within the network.

In terms of characteristics, the GE 197D4613P004 is built to withstand harsh environments. It features a rugged housing that protects against dust, moisture, and vibration, making it suitable for installation in challenging locations. Furthermore, the device is designed with fail-safe mechanisms, which contribute to its reliability and longevity, critical factors in industrial applications where downtime can result in significant financial losses.

Additionally, the GE 197D4613P004 supports various input and output configurations, accommodating a wide range of sensors and actuators. This flexibility enables it to tailor its functionality to specific operational requirements. With built-in diagnostics and troubleshooting capabilities, the device simplifies maintenance procedures, allowing for quicker identification of issues and reducing the risk of unexpected failures.

In conclusion, the GE 197D4613P004 stands out for its combination of advanced technology and rugged design, making it a preferred choice for professionals in the power generation and distribution sectors. Its ability to provide precise control and monitoring, along with its adaptability to various systems, makes it a vital component in enhancing operational efficiency and reliability in challenging industrial environments.
Top Page Image Contents