About the automatic icemaker.

A newly-installed refrigerator may take 12–24 hours to begin making ice.

Icemaker

Power Switch

Feeler Arm

 

Automatic Icemaker (on some models)

When the refrigerator has been connected to the water supply, slide the power switch to the ON position.

The icemaker will fill with water when

it cools to 15°F. When the bin fills to the level of the feeler arm, the icemaker will stop producing ice.

Be sure nothing interferes with the sweep of the feeler arm.

Throw away the first few batches of ice to allow the water line to clear.

The icemaker will produce seven cubes

SHUF\FOH³DSSUR[LPDWHO\² cubes in a 24-hour period, depending on freezer compartment temperature, room temperature, number of door openings and other use conditions.

You will hear a buzzing sound each time the icemaker fills with water.

About the water filter cartridge. (On some models.)

Water filter cartridge

The water filter cartridge is located in the back upper right corner of the refrigerator compartment.

Installing the filter cartridge

Fill the replacement cartridge with water from the tap to allow for better flow from the dispenser immediately after installation.

When to replace the filter on models with a replacement indicator light

There is a replacement indicator light for the water filter cartridge on the dispenser. This light will turn orange to

tell you that you need to replace the filter soon.

The filter cartridge should be replaced when the replacement indicator light turns red or if the flow of water to the dispenser or icemaker decreases.

When to replace the filter on models without a replacement indicator light

The filter cartridge should be replaced every six months or earlier if the flow of water to the dispenser or icemaker decreases.

Line up the arrow on the cartridge and the cartridge holder. Place the top of the new cartridge up inside the holder.

Do not push it up into the holder.

Slowly turn it to the right until the filter

 

cartridge stops. DO NOT OVERTIGHTEN.

Cartridge

As you turn the cartridge, it will

Holder

 

ridge

automatically raise itself into position.

older

The cartridge will move about a ½ turn.

 

Run water from the dispenser for 1-1/2 gallons (about three minutes) to clear the system and prevent sputtering.

Press and hold the RESET WATER FILTER pad (on some models) on the dispenser for three seconds.

NOTE: A newly installed water filter cartridge may cause water to spurt from the dispenser.

Removing the filter cartridge

If you are replacing the cartridge, first remove the old one

by slowly turning it to the left. Do not pull down on the cartridge. A small amount of water may drip down.

CAUTION: To reduce the risk associated with property damage due to water leakage, read and follow instructions before installation and use of this system. Installation and use MUST comply with all state and local plumbing codes.

Filter bypass plug

You must use the filter bypass plug when a replacement filter cartridge is not available. The dispenser and the icemaker will not operate without the filter or filter bypass plug.

Filter Bypass

Filter Bypass

ter

Plug

Plug

 

 

ss

SmartWater

Water by Culligan

 

 

ug

To use the filter bypass plug on Water by Culliganmodels,

you must first remove the filter adaptor from the cartridge holder by turning it to the left.

WARNING

To reduce the risk associated with choking, do not allow children under 3 years of age to have access to small parts during the installation of this product. The disposable filter cartridge should be replaced every

6 months at the rated capacity, or sooner if a noticeable reduction in flow rate occurs.

For the maximum benefit of your filtration system, GE recommends the use of GE-branded filters only. Using GE-branded filters in GE and Hotpoint® refrigerators provides optimal performance and reliability. GE filters

meet rigorous industry NSF standards for safety and quality that are important for products that are filtering your water. GE has not qualified non-GE-branded filters for use in GE and Hotpoint refrigerators and there is no assurance

that non-GE-branded filters meet GE's standards for quality, performance and reliability.

If you have questions, or to order additional filter cartridges, visit our website at www.gewaterfilters.com or call GE Parts and Accessories, 800.626.2002.

Customers in Canada should consult the yellow pages for the nearest Camco Service Center.

8

Page 8
Image 8
GE 20, 22 manuel dutilisation About the water filter cartridge. On some models, Automatic Icemaker on some models

22, 20 specifications

The GE 20,22 series engines represent a significant evolution in aviation technology, embodying advancements that enhance efficiency, reliability, and environmental sustainability. As part of General Electric's commitment to innovation in aerospace propulsion, these engines are designed to meet the rigorous demands of modern commercial aviation while minimizing their environmental footprint.

One of the main features of the GE 20,22 engines is their high bypass ratio, which plays an integral role in achieving improved fuel efficiency. By maximizing the amount of air bypassing the engine core, these engines produce more thrust without a proportional increase in fuel consumption. This characteristic makes them ideal for long-haul operations, effectively reducing operating costs for airlines.

The engines also incorporate advanced materials and manufacturing techniques. The use of lightweight composite materials in fan blades and cases contributes to overall weight reduction, enhancing performance without sacrificing durability. Additionally, the integration of advanced ceramic matrix composites (CMCs) in critical components allows for higher operating temperatures, thereby increasing efficiency and reducing emissions.

Technologically, the GE 20,22 series engines are equipped with state-of-the-art digital control systems. These systems provide precise monitoring and adjustments during operation, leading to optimal performance and reduced maintenance requirements. The implementation of real-time data analytics allows for predictive maintenance, enabling operators to anticipate issues before they arise, thereby improving overall reliability.

Noise reduction is another critical characteristic of the GE 20,22 engines. They feature designs and technologies that significantly diminish noise levels during operation, addressing the growing concerns of communities around airports. This commitment to reducing noise, in conjunction with lower emissions, aligns with global efforts to create a more sustainable aviation industry.

Finally, the GE 20,22 engines are compatible with alternative fuels, showcasing General Electric’s forward-thinking approach to sustainability. As the aviation sector moves towards greener solutions, these engines are positioned to use biofuels and synthetic fuels, further decreasing their ecological impact.

In conclusion, the GE 20,22 series engines embody the latest in aerospace technology with their efficiency, reduced emissions, advanced materials, and noise reduction capabilities. Their design not only meets the needs of today’s airlines but also contributes to the industry's path towards a more sustainable future.