NX-8V2 Control 15
18 CUSTOM COMMUNICATOR FORMAT (See loc 2, 8, &14)
Segment 1: Segment 2:
1 = On for 1800hz transmit; Off for 1900hz.
2 = On for 2300hz handshake; Off for 1400hz.
3 = On for cksum parity; Off for double round parity.
4 = On for 2 digit event code; Off for 1 digit event code.
5 = Reserved.
6 = Reserved.
7 = On for 20 p.p.s.; Off for 10 or 40 p.p.s.
8 = On for 10 p.p.s.; Off for 20 or 40 p.p.s.
1 = On for pager format (no handshake required).
2 = On for 1400/2300 handshake.
3 = Reserved
4 = Reserved.
5 = On for Contact ID.
6 = On for SIA.
7 = On for Contact ID or 4+3.
8 = On for DTMF.
Segment 3 & 4: Reserved
L 19 DOWNLOAD ACCESS CODE 8.............numerical
Location 19 contains the eight-digit access code the NX-8V2 must receive from the downloading software before the panel will permit
downloading to occur. The factory default code is 84800000.
L 20 NUMBER OF RINGS TO ANSWER 1.............numerical
Location 20 contains the number of rings to answer for a download. Enter a number from A0" (disabled) to "15". Factory default is "8"
and the NX-8V2 will answer on 8 rings.
L 21 DOWNLOAD CONTROL 1.............feature select
Location 21 contains the feature selections for the controlling of download sessions. The following features can be enabled or disabled
using this location. (Refer to Glossary beginning on page 46)
Segment 1:
1 = On enables two call answering machine defeat.
2 = On enables tone sniff answering machine defeat.
3 = On requires call back before download session.
4 = Shutdown
5 = On locks all local programming
6 = On locks programming of all locations associated with the communicator
7 = On locks out download section. (If "On", locations 19 - 22 cannot be viewed from the keypad; can only be viewed from the
keypad when "Off".)
8 = On enables call back at auto test interval.
L 22 DOWNLOAD CALL BACK NUMBER 20...........numerical
If a telephone number is programmed into this location, and "Require Callback" is enabled in location 21, the control panel will hang up
for approximately 36 seconds (ensuring that the calling party has disconnected), and then call back. If tone dialing is desired, program
an "15" in the segment where tone dialing should begin. If the entire number should be tone dialing, program an A15" in the first
segment. Four-second delays can be obtained anywhere in the sequence by programming a "13" in the appropriate delay location.
THE CALLBACK PHONE NUMBER SHOULD ALWAYS BE REVIEWED FOR ACCURACY BEFORE
DISCONNECTING.
L 23 PARTITION 1, FEATURE & REPORT SELECTIONS 5.............feature select
Location 23 is used to enable certain features that can be accessed or are visible to the user from the keypad of the system. In
addition, certain communicator reports are enabled in location 23. Each of these features can be enabled by partition. For additional
partition information see locations 88-109 on pages 25- 27. If the feature selection location for any partition is left blank, that
partition will use this location for the feature selection. (For specific definitions, refer to the Glossary beginning on page 46)
Segment 1:
1 = On enables the Quick Arm feature.
2 = On enables the Re-exit feature.
3 = On enables the Automatic Bypass feature.
4 = On enables the Silent Keypad Panic feature (overrides the audible panic selection).
5 = On enables the Audible Keypad Panic feature.
6 = On enables the Keypad Aux 1 feature (FIRE).
7 = On enables the Keypad Aux 2 feature (MEDICAL).
8 = On enables the Keypad Multiple Code Attempt Tamper feature.
Options 4, 5, 6,
and 7 can only be
viewed from the
keypad. These options
must be changed
through downloading.