26 NX-8V2 Control
92 ACCOUNT CODE FOR PARTITION 3 6............ numerical
The account code sent when partition 3 is reported is programmed in location 92. If location 92 is left unprogrammed (all A10") then
the account code corresponding to the Phone number dialed will be used. If the account code is less than six digits, program a
A10" in the segment immediately after the last digit of the account code. If the account code is 6 digits long program all 6 segments.
93 PARTITION 3 FEATURE & REPORTING SELECTIONS 5............ feature select
Location 93 is used to enable certain features that can be accessed or are visible to the user from the keypad of the system. In
addition, certain communicator reports are enabled in this location. Each of these features can be enabled by partition. This location
contains 5 segments, with eight possible features per segment. Refer to Location 23 (page 15) for the feature selections. If all
segments are blank (nothing enabled), the features for partition 1 will be used.
94 PARTITION 3 ENTRY EXIT TIMERS 6............ numerical
Location 94 is used to enter in seconds the Entry and Exit times. There are 2 separate entry and exit times. Valid entries are 10-255
seconds. If all segments are A0", the entry and exit times for partition 1 will be used.
Segment 1, Entry time 1: Entry time that will be used when a Delay 1 zone type initiates an entry delay.
Segment 2, Exit time 1: Exit time that will be used for all zones designated as Delay 1.
Segment 3, Entry time 2: Entry time that will be used when a Delay 2 zone type initiates an entry delay.
Segment 4, Exit time 2: Exit time that will be used for all zones designated as Delay 2.
Segments 5 & 6: Reserved
95 ACCOUNT CODE FOR PARTITION 4 6............ numerical
The account code sent when partition 4 is reported is programmed in location 95. If location 95 is left unprogrammed (all A10") then
the account code corresponding to the Phone number dialed will be used. If the account code is less than six digits, program a
A10" in the segment immediately after the last digit of the account code. If the account code is 6 digits long, program all 6 segments.
96 PARTITION 4 FEATURE & REPORTING SELECTIONS 5............ feature select
Location 96 is used to enable certain features that can be accessed or are visible to the user from the keypad of the system. In
addition, certain communicator reports are enabled in this location. Each of these features can be enabled by partition. This location
contains 5 segments, with eight possible features per segment. Refer to Location 23 (page 15) for the feature selections. If all
segments are blank (nothing enabled), the features for partition 1 will be used.
97 PARTITION 4 ENTRY EXIT TIMERS 6............ numerical
Location 97 is used to enter in seconds the Entry and exit times. There are 2 separate entry and exit times. Valid entries are 10-255
seconds. If all segments are A0", the entry and exit times for partition 1 will be used.
Segment 1, Entry time 1: Entry time that will be used when a Delay 1 zone type initiates an entry delay.
Segment 2, Exit time 1: Exit time that will be used for all zones designated as Delay 1.
Segment 3, Entry time 2: Entry time that will be used when a Delay 2 zone type initiates an entry delay.
Segment 4, Exit time 2: Exit time that will be used for all zones designated as Delay 2.
Segments 5 & 6: Reserved
98 ACCOUNT CODE FOR PARTITION 5 6............ numerical
The account code sent when partition 5 is reported is programmed in location 98. If location 98 is left unprogrammed (all A10") then
the account code corresponding to the Phone number dialed will be used. If the account code is less than six digits, program a
A10" in the segment immediately after the last digit of the account code. If the account code is 6 digits long, program all 6 segments.
99 PARTITION 5 FEATURE & REPORTING SELECTIONS 5............ numerical
Location 99 is used to enable certain features that can be accessed or are visible to the user from the keypad of the system. In
addition, certain communicator reports are enabled in this location. Each of these features can be enabled by partition. This location
contains 5 segments, with eight possible features per segment. Refer to Location 23 (page 15) for the feature selections. If all
segments are blank (nothing enabled), the features for partition 1 will be used.
100 PARTITION 5 ENTRY EXIT TIMERS 6............ numerical
Location 100 is used to enter in seconds the Entry and exit times. There are 2 separate entry and exit times. Valid entries are 10-255
seconds. If all segments are A0", the entry and exit times for partition 1 will be used.
Segment 1, Entry Time 1: Entry time that will be used when a delay 1 zone type initiates an entry delay.
Segment 2, Exit Time 1: Exit time that will be used for all zones designated as delay 1.
Segment 3, Entry Time 2: Entry time that will be used when a delay 2zone type initiates an entry delay.
Segment 4, Exit Time 2: Exit time that will be used for all zones designated as delay 2.
Segments 5 & 6: Reserved
101 ACCOUNT CODE FOR PARTITION 6 6............ numerical
The account code sent when partition 6 is reported is programmed in location 101. If location 101 is left unprogrammed (all A10")
then the account code corresponding to the Phone number dialed will be used. Program the account code is less than six digits,
program a A10" in the segment immediately after the last digit of the account code. If the account code is 6 digits long, program all 6
segments.