Installation Preparation
DUCT COVER ACCESSORIES
A duct cover accessory is required for recirculating operation. Use this chart to determine which accessory is required for your ceiling height.
ZV750SY Installation Heights
Actual | * Possible Hood | Recirculating | ||
Ceiling | ||||
Height | Installation Height | Accessory | ||
|
|
|
| |
7′ 11″ |
| |||
8′ 0″ |
|
| ||
8′ 1″ | 58C | |||
8′ 2″ | ||||
|
| R7 | ||
8′ 3″ | ||||
|
| ZX | ||
8′ 4″ | ||||
8′ 5″ | Y | |||
ACCESSOR | ||||
8′ 6″ | ||||
| ||||
|
|
| ||
8′ 7″ |
| |||
8′ 8″ |
| |||
8′ 9″ |
| |||
8′ 10″ |
| |||
8′ 11″ |
| |||
9′ 0″ |
| |||
9′ 1″ |
| |||
|
|
| C | |
9′ 2″ | ||||
510 | ||||
|
| |||
9′ 3″ |
| |||
|
|
| 7 | |
9′ 4″ | ||||
XR | ||||
|
|
| ||
9′ 5″ | ||||
YZ | ||||
9′ 6″ | ||||
|
|
| ACCESSOR | |
9′ 7″ | ||||
| ||||
9′ 8″ |
|
| ||
|
|
| ||
9′ 9″ |
| |||
|
|
| ||
9′ 10″ |
| |||
|
|
| ||
9′ 11″ |
|
| ||
|
|
| ||
10′ 0″ |
|
* Based on 36″ countertop height.
ZV750SY Duct Cover Dimensions | ||||
Hood and |
|
| ||
| B |
| ||
Accessory | A | B | ||
ZXR758C | ||||
| ||||
ZXR7510C | A | |||
|
|
| ||
|
|
|
4
POWER SUPPLY
IMPORTANT – (Please read carefully)
WARNING:
FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE PROPERLY GROUNDED.
Remove house fuse or open circuit breaker before beginning installation.
Do not use an extension cord or adapter plug with this appliance. Follow National Electrical Code or prevailing local codes and ordinances.
Electrical supply
This vent hood must be supplied with 120V, 60Hz, and connected to an individual, properly grounded branch circuit, and protected by a 15 or 20 amp circuit breaker or time delay fuse.
•Wiring must be 2 wire with ground.
•If the electrical supply does not meet the above requirements, call a licensed electrician before proceeding.
•Route house wiring as close to the installation location as possible. Wiring should enter at least 4" above the bracket on the right side.
•Connect the wiring to the house wiring in accordance with local codes.
Grounding instructions
The grounding conductor must be connected to a ground metal, permanent wiring system, or an
WARNING: The improper connection of the
TOOLS AND MATERIALS
REQUIRED (NOT SUPPLIED)
• Tape measure | • 10 mm Hex wrench/socket |
• Knife | • Safety glasses |
• Spirit level | • Duct tape |
• Wire cutter/stripper | • Gloves to protect against sharp |
• Wire nuts | edges |
• Electric drill and | • 120V 60Hz. 15 or 20 Amp, 2 wire |
appropriate bits | with ground. Properly grounded |
• Phillips and flat blade | branch circuit. |
screwdrivers | • Strain relief for junction cover. |
• Hammer | • 6" round duct, length to suit |
• Pliers | installation. |
• Center punch |
|